FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-109

PDF page 527 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 527
AC 27-1B · E-109Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


and is the maximum likely to be encountered in service. Rotorcraft, which have been
certified to the ¼-mile visibility test criteria, have not shown engine inlet snow-related
service difficulties.  It is important to note that the visibility specified is a test parameter
rather than an operational limitation to be imposed on the rotorcraft after the tests are
completed.

              (B) Temperature.

                   (1) The ambient temperature specified is conducive to wet snow
conditions. Wet snow tends to accumulate on unheated surfaces subject to
impingement.

                   (2) Colder ambients, more conducive to dry snow conditions, may be
critical for some induction systems. Colder exterior surfaces may be bypassed, and the
snow crystals may stick to partially heated interior surfaces where partial melting and
refreezing may occur.

                   (3) Company development testing or experience with very similar type
induction systems may be adequate to determine the critical ambient conditions for
certification testing.

             (C) Operations.

                   (1) Ground running, taxiing, and IGE hover operations are generally
the most critical since the rotorcraft may be operating in recirculating snow. Twenty-five
minutes under these extreme conditions would seem a reasonable maximum, both from
the view of pilot stress and the maximum expected taxi time prior to takeoff in bad
weather.

                   (2) One hour of level flight operation under ¼-mile visibility snow
conditions should provide ample opportunity for hazardous accumulations to begin to
build.

                   (3) The descent and landing will provide an engine power change, an
induction system airflow change, and a variation in the external airflow pattern near the
induction system entrance. The initiation of the descent and final flare for landing may
also produce additional airframe vibration transmitted to the induction system. These
power, airflow, and vibration changes may provide an opportunity for any level flight
accumulations to be ingested into the engine. Hazardous accumulations are not
acceptable during or after any test phase.

                   (ii) Visibility may fluctuate rapidly in snowstorms.  It is affected by the
presence of fog or ice crystals, is not crew measured or controlled, and is difficult to
estimate. A visibility operational limitation based on snow, therefore, is not appropriate.



                                                         Page E - 109

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →