Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
are impractical. The rotor downwash effect should be considered to the extent possible
by adjusting the inflow angle in the tunnel.
(2) The power loss (bleed air, generator load, etc.) attributable to the
heating requirements will affect the performance of the rotorcraft. Normally, this may be
accounted for by specifying a gross weight incremental deduction from the flight manual
performance data for flight into visible moisture below 41°F (+5°C).
(3) Special evaluation of the possibility of ice ingestion damage to the
engine should be made for heated systems, which considers the ice ingestion to be
expected when the anti-ice system is actuated after a delay of 1 minute for the pilot to
recognize that the rotorcraft has encountered ice. This time delay may be reduced if the
crew is provided adequate distinctive cues to alert them that the rotorcraft has
encountered icing conditions.
(B) For unheated inlets, an acceptable method for showing compliance
would include an extensive, detailed analysis (which shows that ice accretions on and in
the inlet do not seriously obstruct adequate airflow to the engine) and tests as
necessary to validate the analysis. The analysis of ice accretion becomes even more
questionable since the unheated inlet involves ice buildups which themselves
progressively change shape during icing exposure.
(1) Flight testing with an instrumented rotorcraft in natural ice to verify
the analysis is desirable; however, wind tunnel tests as discussed above may be used.
Since unheated inlets typically continue to accrete ice as a function of exposure, both
the analysis and the test should realistically consider the actual exposure to be
expected in service. This should not be less than penetration of the continuous
maximum icing cloud followed immediately by exposure to the intermittent maximum
cloud for rotorcraft not certified for icing. Engine power changes which may be
expected in service should be included in the testing, and a warm-up period at the
conclusion of the icing exposure should be shown for some selected test points to
evaluate potential ice breakaway and ingestion.
(2) For the non-icing certified rotorcraft using the limited icing
exposure concept for inlet certification, some conservatism should be applied to account
for the fact that inlet icing may occur without airframe icing, and that the escape
procedure from this unapproved operating condition is not defined. A demonstration of
30-minute hold capability in the continuous maximum cloud would be acceptable.
Alternatively, if positive cues (perhaps a carefully located ice detector) of potential inlet
icing are provided to the crew, the time increment could be reduced to recognition plus
15 minutes (15-minute escape time after recognition is consistent with the single ice
protection system failure recognition and escape guidance for aircraft ice protection
systems in section 29.1419 of AC 29-2C). It should not be assumed that airframe icing
will always be available as a cue to potential inlet icing. The main rotor, for example,
may not show icing indications above 25°F (-4°C), whereas some inlets may ice
critically near 32°F (0°C) ambient. A reduction of the acceptable 30-minute exposure
Page E - 105
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.