Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
should not be based on observation of ice accretions on protruding components which
are likely to be changed. For example, a limited exposure inlet icing program which
reduces the inlet icing exposure time based on crew recognition of icing on the
windshield wipers may be invalidated at a later date if a new windscreen deletes the
wipers.
(iii) Inlet capability during IGE hover in icing conditions has not generally
been considered for rotorcraft not certified for icing. However, the FAA/AUTHORITY is
aware that some inlets may ice at zero airspeed near 32°F (0°C) with no indications of
airframe icing in the field of view of the crew. This special concern of operating within
RFM limitations, and yet placing the induction system in jeopardy, may be addressed in
several ways. If the induction system ice protection scheme is not dependent on
airspeed for proper function, the issue may be addressed by tunnel testing with inlet
airflows approximating hover with no particular attention to tunnel windspeed. For
protection schemes which may be sensitive to airspeed (external screens have shown
this tendency), actual hover demonstration at or near zero speed tunnel conditions may
be appropriate. Icing detectors located to indicate induction system icing in hover may
be an option to a hover icing protection demonstration. On an external screened
configuration, the FAA/AUTHORITY has accepted a satisfactory IGE hover
demonstration of 30 minutes at the critical ambient temperature (i.e., ambient consistent
with no airframe icing but potential inlet icing), 0.6 grams/meter3 LWC, and 40-micron
droplet size as an adequate response to this concern.
(iv) For aircraft requesting full icing approval, or for those electing to show
continuous induction system icing protection, the forward flight icing exposure would not
be less than that time required to stabilize any ice accretions observed during repeated
cycles of the continuous maximum followed by intermittent maximum cloud exposure.
Typically, any ice accretions resulting from these repeated cycles would be expected to
stabilize in less than 30 minutes. The 30-minute hold capability in the continuous
maximum icing environment could thus be assured without special testing by careful
selection of the test points for this repeated cycle.
(v) A rotorcraft requesting full icing approval should also have hover
capability in the icing environment. Intermittent maximum icing conditions are not likely
to exist near ground level and a satisfactory demonstration could involve the ability to
hover indefinitely in the continuous maximum icing environment. Alternatively, carefully
worded RFM limitations to restrict hover time may be acceptable if the system is not
capable of indefinite exposure. Hover capability verification may not involve zero
airspeed demonstration if the inlet protection system is insensitive to rotorcraft airspeed.
(vi) The engine(s) must be installed or protected to avoid engine damage
from ice ingestion due to ice accretion in the inlet or on other parts of the rotorcraft,
including the rotors, which may break away to enter the inlet. If screens or bypass
arrangements are provided for these purposes, they should be included in the icing
tests and shown by test or rational analysis to effectively protect the engine.
Page E - 106
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.