FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-98

PDF page 516 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 516
AC 27-1B · E-98Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

climb, various cruise speeds and altitudes, hover, shutdown after prolonged hover, and
sling load cooling if a sling is used. Any other appropriate test conditions and
procedures necessary to demonstrate adequate cooling for water, ground, flight,
emergency, and shutdown conditions should be addressed in the test proposal. For
multiengine rotorcraft (particularly in regard to transmission cooling), one test point that
should be investigated is the point of highest multiengine mechanical power at the
maximum ambient temperature. Other significant test conditions to be considered for
multiengine rotorcraft are the OEI test conditions. The selection of all test points should
be tempered with engineering judgment and should consider test points and procedures
used on previous, similar rotorcraft certification work, if available.

         (2) Compliance with § 27.1045(b) is typically shown by use of existing cockpit
instrumentation or add-on test instrumentation from which temperature data are read
prior to and during test segments. Test plans should clearly identify what is to be used
and who is authorized to make and record readings and the accuracy and current
calibration requirements for test instrumentation.

         (3) Compliance with § 27.1045(c) is typically shown during FAA/AUTHORITY
authorized testing by conducting each test segment until at least one of the three criteria
(temperature stabilization, flight test segment completion, or an operating limitation) is
reached.  If an adverse operating limitation is reached, such as overheating, or the test
cannot otherwise be successfully completed, then compliance has not been shown and
a reevaluation is required.

AC 27.1045A.   § 27.1045 (Amendment 27-23) COOLING TEST PROCEDURES.

     a. Explanation. Amendment 27-23 clarifies acceptance criteria for the powerplant
cooling tests that are appropriate if, during the cooling test, component temperatures
peak and then decline rather than stabilize. In these instances, the previous
requirement to continue the test until “stabilization” occurred was unduly restrictive and
was eliminated.

     b. Procedures. All of the policy material pertaining to this section remains in effect
except that the engine fluid temperatures do not have to stabilize.
Paragraph AC 27.1045 currently lists three criteria for test completion: temperature
stabilization, flight test segment completion, or an operation limitation. With
Amendment 27-23, a fourth criteria for test completion is: 5 minutes after the peak
temperature is reached, the test can be considered complete.





Page E - 98

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →