FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-97

PDF page 515 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 515
AC 27-1B · E-97Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

engine has 15° C “field margin” which would allow the engine temperature to gradually
increase 15° C to maintain a given power as engine life is utilized. Secondly, the
measured gas temperature corresponding to hot day power required at maximum gross
weight is less than that corresponding to either the drive system limit or twin-engine hot
day power available. Thus, the thermal limit correction could be applied from the test
day MGT, 600° C, to the power required MGT plus the field margin, 650° C plus 15° C,
rather than applying the correction factor to the full thermal capability of the engine,
765° C.

                   (ii)   Care should be used in applying this relieving method, because as the
hover altitude changes, the maximum gross weight and power required (and the
associated MGT) will vary. The data must be corrected to at least the maximum MGT
for a minimum specification engine that can occur in service at the flight condition under
investigation.

AC 27.1045.    § 27.1045 COOLING TEST PROCEDURES.

     a. Explanation.

         (1) Section 27.1045(a) requires that cooling tests be conducted for the
rotorcraft in the configurations and under the conditions most critical for cooling.

         (2) Section 27.1045(b) requires that a temperature be stabilized prior to start of
a cooling test for any test rotorcraft and any test stage. This is to ensure that the
system reaches the maximum temperature from which it must be cooled. Temperature
stabilization is achieved when the rate of change is less than 2° F per minute.
Therefore, for each test rotorcraft in each test phase, the temperature must be stabilized
prior to entry into flight test.  If temperature stabilization cannot be achieved as a normal
result of the entry condition, then operation through the full entry condition must be
accomplished prior to entry into the flight test segment being conducted. This allows
the temperatures to reach their maximum natural levels prior to test initiation. Also, for
each test rotorcraft during the takeoff stage of flight, the climb at takeoff power must be
preceded by a hover during which temperature stabilization is achieved.

         (3) Section 27.1045(c) requires that a test must be conducted for each flight
stage until either the temperatures stabilize, the flight test stage is completed, or an
operating limitation is reached.

     b. Procedures.

         (1) To comply with § 27.1045(a), an applicant typically submits a cooling test
proposal to the FAA/AUTHORITY for approval. The proposal should encompass
detailed procedures to demonstrate cooling capability for each critical rotorcraft
configuration and test condition (test point).  If a single-most critical test configuration
and condition is not readily identifiable (which is usually the case), then a series of
cooling tests must be conducted. Typical cooling test segments are climb, takeoff and


                                                       Page E - 97

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →