Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(1) For each oil strainer or filter required by § 27.1019(a) which has a bypass,
the bypass should be sized to allow oil flow at the normal rate through the oil system
with the filtration means completely blocked.
(2) For each oil strainer or filter installed per this rule, the capacity must be
such that when operating with oil contaminated to a degree greater than established
during engine certification, the oil flow and pressure are within the operating limits
established for the engine. The mesh requirements are determined by the engine
installation documents for the filtration of particle size and density.
(3) Unless the filter is located at the oil tank outlet, § 27.1019(a)(3) requires an
indicator that will show when the contaminant level of the filtration system, as specified
in § 27.1019(a)(2), has been reached. The indicator should signal a contaminant level
which will allow completion of the flight before the filter would enter a bypass condition.
The indicator may be a pop-out button or other maintenance cue that is checked on
each preflight.
(4) An evaluation of the construction and location of the bypass associated with
the strainer or filter should be accomplished. The appropriate installation of the filter
based on this evaluation would preclude the release of the collected contaminants in the
bypass oil flow.
(5) If an oil strainer or filter installed in compliance with this regulation does not
have a bypass, there must be a means to connect it to the warning system required in
§ 27.1305(r). This warning should indicate to the pilot the contamination before it
reaches the capacity established in § 27.1019(a)(2).
(6) Section 27.1019(b) covers the blocked oil filter requirements associated
with reciprocating engine installations. The lubrication system should be such that the
normal oil flow will occur with the filter completely blocked.
AC 27.1019A. § 27.1019 (Amendment 27-23) OIL STRAINER OR FILTER.
a. Explanation. Amendment 27-23 relaxed an unduly restrictive requirement for
an “indicator” to indicate the contamination level of oil filters. The rule change allows
acceptance of a “means to indicate” the contaminate level to allow a wider range of
acceptable methods of compliance.
b. Procedures. All of the policy material pertaining to this section remains in effect
except that an “indicator” is not required to indicate the contamination level of the oil
filters. Unless the filter is located at the oil tank outlet, § 27.1019(a)(3) requires that the
oil strainer or filter have the means to indicate when the contaminant level of the
filtration system, as specified in § 27.1019(a)(2), has been reached. If an indicator is
installed, it should signal a contaminant level that will allow completion of the flight
Page E - 89
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.