FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-83

PDF page 501 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 501
AC 27-1B · E-83Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (1) The filter should be mounted in a horizontal segment of the fuel line to
facilitate proper action of the sediment bowl.  If the filter is located above the fuel tank, it
becomes necessary to activate a fuel boost pump to achieve positive drainage of the
filter bowl. Without pump pressure, air may enter the fuel system during the filter
draining operation and, for turbine engines, result in transient power surges or engine
failure during subsequent engine operation. A flight manual note to require pump(s) to
be “on” during filter draining would be appropriate.

         (2) Section 27.997(d) sets forth a requirement for filter capacity. The capacity
requirement may be substantiated by showing that the filter, when partially blocked by
fuel contaminates (to a degree corresponding to the indicator marking or setting
required by § 27.1305(a)), does not impair the ability of the fuel system to deliver fuel at
pressure and flow values established as minimum limitations for the engine. The filter
mesh must be sized to prevent passage of particulate matter which cannot be tolerated
by the engine. Part 33 requires that the degree and type of filtration be established for
the engine. This information, available in the FAA/AUTHORITY-approved Engine
Installation Manual, should be the basis for selection of the airframe filter mesh.
Although a test may be devised and conducted, data from the filter manufacturer usually
are acceptable to verify compliance. Note that when the filter capacity is reached,
continued flow of contaminated fuel may result in engine failure. A flight manual note
regarding precautionary procedures is appropriate.

         (3) Part 33 (through Amendment 33-6) has an identical requirement for a fuel
filter for engine fuel systems; however, it is not intended that two filters should be
required.

AC 27.997A.    § 27.997 (Amendment 27-23) FUEL STRAINER OR FILTER.

     a. Explanation. Amendment 27-26 requires that a fuel strainer or filter should be
installed between the fuel tank outlet and the first fuel system component that is
susceptible to fuel contamination. Components that will be protected from
contamination include but are not limited to fuel metering devices which control flow
rate, fuel heaters, and positive displacement pumps. The amendment also requires a
sediment bowl and drain (unless the bowl is readily removable for drain purposes) to
facilitate separation of solid and liquid contaminants from the fuel.

     b. Procedures.

         (1) The fuel strainer or filter should be accessible for draining and cleaning.  It
should incorporate a screen or other element that is easily removable.  It should be
mounted so that its weight is not supported by the inlet or outlet connections of the
strainer itself, unless it can be shown that adequate strength margins exist in the lines
and connections.





                                                       Page E - 83

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →