FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-84

PDF page 502 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 502
AC 27-1B · E-84Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (2) The fuel strainer or filter should have a sediment trap and drain (unless the
trap is readily removable for drain purposes). The volume capacity of the sediment trap
is specified in § 27.971(a) (0.10 percent of the tank capacity or 1/16 of a gallon).

         (3) The fuel strainer or filter mesh should provide the filtration stipulated in the
FAA/AUTHORITY-approved engine installation manual that is prepared for the type
certificated engine (FAR Part 33).

         (4) The fuel strainer or filter should have the capability to remove any
contaminant that would jeopardize the flow of fuel that is necessary to meet the
requirements of § 27.955. In addition, the strainer or filter should have a bypass system
with an impending bypass indicator (Refer to § 27.1305(a)(17)). When the strainer or
filter is partially blocked with contaminants, to the degree that the fuel flow requirements
of § 27.955 can no longer be achieved, the impending bypass indicator should be
activated. At this point, the strainer or filter should not yet be bypassing unfiltered fuel.
Although a test may be devised and conducted, data from the filter manufacturer usually
are acceptable to verify compliance. Note that when the filter capacity is reached,
continued flow of contaminated fuel may result in engine failure. A flight manual note
regarding precautionary procedures is appropriate.

         (5) Section 33.67(b) has an identical requirement for a fuel filter for engine fuel
systems; however, it is not intended that two filters should be required.

AC 27.999.  § 27.999 (Amendment 27-11) FUEL SYSTEM DRAINS.

     a. Explanation. This regulation provides for fuel system drains and defines the
requirements which the system must meet.

     b. Procedures.

         (1) The location and function of the fuel system drains are an integral part of
any fuel system. There may be several drains required dependent upon the fuel system
design. Each fuel tank sump and certain types of fuel strainers or filters require a
means to drain (reference §§ 27.971 and 27.997).

         (2) Selection of the location and orientation of the drain discharge in the design
phase is important to assure that there is no impingement on any part of the rotorcraft.
To show compliance with the requirement may require tests dependent upon whether
the applicant has a previously approved design which is similar or if the system is a new
design for which no previous experience is available.

         (3) The location of the drain valve should be selected so that the requirements
for accessibility, ease of operation, and protection are met.

         (4) Spring-loaded fuel drain valves conforming to MIL-V-25023B, TSO-C76, or
equivalent, may be approved as “positive locking” valves for those installations where


Page E - 84

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →