FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-81

PDF page 499 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 499
AC 27-1B · E-81Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

provided with a means to determine that a main pump failure has occurred so that it can
be replaced in a timely manner.

AC 27.991A.    § 27.991 (Amendment 27-23) FUEL PUMPS.

     a. Explanation. Amendment 27-23 revised § 27.991 to clarify fuel pump
redundancy requirements. Redundancy for fuel pump failure includes consideration of
both the pump and the pump motivating device.

     b. Procedures. All of the policy material pertaining to this section remains in effect
with the following clarification: Airframe supplied fuel pumps that are intended for use
only during engine starting are not considered as “main” airframe pumps and do not
require “emergency” backup pumps.

AC 27.993.  § 27.993 (Amendment 27-2) FUEL SYSTEM LINES AND FITTINGS.

     a. Explanation. This rule outlines design requirements for fuel system lines.

     b. Procedures.

         (1) Compliance is usually obtained by employing routing and clamping as
described in paragraph 709, Chapter 14, Section 2, of AC 43.13-1A and by monitoring
the arrangement throughout the developmental and certification test period.
Requirements for approved flexible lines may be resolved by utilizing lines listed as
TSO C53a approved for installation in either normal or high temperature areas as
appropriate. The service life of TSO C53a approved high pressure fuel hoses is not
established by regulation. Service life is determined by the aircraft manufacturers and
included in their quality control system which is monitored by the FAA/AUTHORITY.

         (2) Verify that adequate clearance exists between lines and elements of the
rotorcraft control system at extremes of control travel, including control deflections and,
for flexible lines (hoses), possible variations in routing.

         (3) Flexible lines inside fuel or oil tanks require special evaluation to ensure that
the external surfaces of these lines are compatible with the fluids involved and that fluid
sloshing will not cause line failure. Lines inside tanks should be routed to avoid
impingement by fuel or oil filler nozzles.

         (4) Fuel system lines and fittings located in any area subject to engine fire
conditions must comply with the requirements of § 27.1183.

         (5) Compliance with § 27.999 requires that fuel system lines contain no low
points from sagging or looped routing unless drains are provided which will completely
drain the system with the rotorcraft in its normal attitude on level ground.




                                                       Page E - 81

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →