FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-77

PDF page 495 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 495
AC 27-1B · E-77Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

measure the difference between the gas pressure inside each fuel tank expansion
space and the air pressure in the cavity or area surrounding the outside of the fuel tank.

                   (ii)   Conduct ground and flight tests recording the differential pressures
between the inside and the outside of the fuel tanks. The following conditions should be
evaluated:

              (A) Refueling and defueling (if applicable).

              (B) Level flight to VNE.

             (C) Maximum rate of ascent and descent.

                    (iii)  Compare the measured differential pressure values with the maximum
allowable for the fuel tank design being evaluated. For flexible bladder type fuel cells,
the pressure inside the tank should not be significantly less than the surrounding
pressure to avoid the possibility of collapsing the bladder.

AC 27.975A.    § 27.975 (Amendment 27-23) FUEL TANK VENTS.

     a. Explanation. Amendment 27-23 added a new paragraph § 27.975(b) that
requires fuel tank vent systems be designed to minimize fuel spillage and subsequent
fire hazards in the event of rollover of the rotorcraft during landing or ground operation.

     b. Procedures. The policy material pertaining to this section remains in effect.
Additionally, fuel tank vent system design should minimize spillage of fuel in the vicinity
of a potential ignition source in the event of rollover during landing or ground operation.

AC 27.975B.    § 27.975 (Amendment 27-30) FUEL TANK VENTS.

     a. Explanation. In addition to the current requirements, Amendment 27-30 revises
paragraph (b) to add the requirement that the venting system be designed to minimize
fuel spillage through the vents to an ignition source in the event of a fully or partially
inverted rotorcraft fuselage attitude following a survivable impact. (A survivable impact
is defined in paragraph AC 27.952.) Since rotor action on impact and other impact
dynamics have been found in numerous cases to cause rollovers or other unusual
postcrash attitudes, compliance with this paragraph would significantly mitigate the
postcrash fire hazard by minimizing fuel spills through vents to ignition sources when
the postcrash attitude of the rotorcraft would allow gravity and/or post impact sloshing
induced fuel spills through a normally open fuel vent.

     b. Procedures

         (1) In addition to the compliance procedures for the previous amendment;
installation of design features, such as gravity activated shuttle valves in the vent lines
(that are normally open but close under certain predictable, postcrash scenarios that are


                                                       Page E - 77

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →