Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
generated by involvement in a survivable impact that results in either an inverted or
partially inverted fuselage attitude) must be accomplished.
(2) Once selected, the design feature chosen for compliance should be shown
to function effectively without significant leakage by either full scale and/or bench tests
that apply the total pressure forces that correspond to a 100 percent full, 50 percent full,
and 5 percent full fuel load applied to the device in a worst case survivable impact. (If a
critical fuel level can be clearly identified, then only that fuel level and the corresponding
critical total pressure load need be utilized for certification approval.) The total pressure
forces should be determined and applied in a manner that simulates the magnitude and
rate of load onset (due to a combination of gravity and sloshing) that would occur in
otherwise survivable impacts that would involve rollover attitudes of 45 degrees (or the
minimum spillage roll angle), 90 degrees (rotorcraft on its side), and 180 degrees
(rotorcraft fully inverted). (In some designs, the 45-degree attitude may not be the
correct initial roll angle at which fuel spillage through a given vent would begin to occur
due to the placement of the vents on the fuselage. For these cases, the minimum angle
should be determined by analysis.)
(3) Once all test conditions are defined, these tests should be conducted with
all structural deformation present in the test set up that is necessary to simulate the
actual structural deformation either in or applied to the vent line or system in a worst
case survivable impact. The structural deformation to be applied can be determined by
rational analysis, analysis, test, or a combination. Significant leakage is defined as
leakage of 10 drops per minute, or less, after all testing is complete. The criteria of 10
drops per minute, or less, corresponds to the criteria of 5 drops per minute, or less, per
breakaway coupling half (i.e., a total of 10 drops per minute, or less, for the entire
separated coupling) specified in the advisory material for § 27.952 (re:
paragraph AC 27.952).
AC 27.977. § 27.977 (Amendment 27-11) FUEL TANK OUTLET.
a. Explanation.
(1) This provision prescribes a fuel strainer for the fuel tank outlet (suction lift
system) or for the booster pump (boosted systems) for both reciprocating and turbine
engine installations.
(2) This requirement is intended to ensure that relatively large, loose objects
which may be present in the fuel tank do not interfere with fuel system operation. The
provision of § 27.997 should ensure protection from smaller contaminants which may
occur in service.
b. Procedures.
(1) Section 27.977(a) specifies an 8- to 16-mesh-per-inch strainer for
reciprocating engine installations, and a strainer which will prevent passage of any
Page E - 78
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.