FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-76

PDF page 494 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 494
AC 27-1B · E-76Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

period of at least 5 minutes.  If no significant leakage occurs, then compliance has been
shown. Significant leakage is defined as leakage in excess of 10 drops per minute at
any time during or after the 5-minute test.

         (4) Compliance procedures for paragraph (b) are as follows: Visual means,
such as placards and alignment marks, and mechanical means, such as detents and
locking slots, must both be provided. This is necessary to give both a clear visual and
mechanical indication that a filler cap or a filler cap cover is properly installed and fuel
tight after each removal and replacement. Visual indications such as alignment marks,
that show proper installation should be easily read from a distance of at least 5 feet by
anyone making a routine inspection or check.

AC 27.975.  § 27.975 FUEL TANK VENTS.

     a. Explanation.

         (1) Each fuel tank for which an expansion space is required per § 27.969 must
be vented from the top part of the expansion space.

         (2) Fuel tank vents must be designed to minimize the probability of the vent
being restricted or completely clogged by dirt or ice.

         (3) Vents of fuel tanks having interconnected outlets must be interconnected as
required per § 27.963.

     b. Procedures.

         (1) There should be no point in any vent line where moisture can accumulate
with the rotorcraft in the ground attitude or level flight attitude unless drainage is
provided.

         (2) Each vent should be constructed to prevent siphoning of fuel during any
normal operation.

         (3) No vent line or drainage provision should be terminated at a point where the
discharge of fuel from the outlet would constitute a fire hazard or from which fumes
could enter any personnel compartment.

         (4) The vent system capacity and installed configuration should maintain
acceptable differences of pressure between the interior and exterior of tank. Analysis
and/or flight testing may be required to demonstrate this capability depending on the
fuel system design.  If flight testing is required, the following flight test procedure is one
method of verifying proper vent system operation.

                  (i)   Using a rotorcraft with a fuel tank and vent system which conforms to
production design specifications, install differential pressure instrumentation which will


Page E - 76

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →