FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-75

PDF page 493 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 493
AC 27-1B · E-75Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

AC 27.973A.    § 27.973 (Amendment 27-30) FUEL TANK FILLER CONNECTION.

     a. Explanation. The original, single unlettered paragraph of old § 27.973 is
redesignated as paragraph (a) by Amendment 27-30. The new (a) has three
subparagraphs. These changes have been made to both make § 27.973 parallel to
§ 29.973 and to incorporate the new crash resistant fuel system requirements of
§ 27.952 (re: paragraph AC 27.952).

         (1) New paragraph (a) is revised to require that all fuel tank filler connections
be made fuel tight under both normal operations and during a survivable impact in
accordance with the requirements of § 27.952(f) and its associated advisory material.

         (2) New paragraph (a)(1) is added to require that each filler be marked as
prescribed in § 27.1557(c)(1).

         (3) New paragraph (a)(2) is added to require that each recessed filler
connection that can retain an appreciable amount of fuel have a drain that discharges
clear of the rotorcraft.

         (4) New paragraph (a)(4) is added to require that each filler cap provide a fuel
tight seal under the fluid pressures expected in service and in a survivable impact.

         (5) New paragraph (b) is added to require that each filler cap or cap cover warn
when the cap is not fully locked or seated to a fuel tight condition on the filler
connection.

     b. Procedures.

         (1) The compliance procedures for general paragraph (a) are those of
§ 27.952(f) and those described herein for the three subparagraphs to (a).

         (2) The compliance procedures for (a)(1) and (a)(2) can normally be
demonstrated by analysis and physical inspection of the fuel filler design. Testing is not
normally required.

         (3) The compliance procedures for (a)(3) are as follows: The fuel tank filler
connection must be shown to be leak free under the worst case fuel pressures (due to
combination of static pressure and sloshing induced head) from both normal operations
and from a survivable impact. The worst case loads from these two conditions must be
determined. In most cases the load resulting from a survivable impact will prevail. For
the survivable impact, normally the worst case combined pressure loading occurs at the
time of impact at the fuselage that places the filler tube neck (at the vicinity of the filler
cap connection) in a vertical or near vertical attitude. Once the critical load case is
determined by analysis, test, or a combination; the fuel tank filler connection (or an
approved mockup) can be tested for sealing capability by applying a fluid such as water
at the critical pressure at the critical attitude of the tube (with the cap inverted) for a


                                                       Page E - 75

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →