FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-74

PDF page 492 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 492
AC 27-1B · E-74Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


               (iv)  When no more fuel can be removed from the tank with the rotorcraft
fuel supply system, return the rotorcraft to a normal ground attitude. Completely drain
the sump of the tank or tanks being tested into a container and measure the volume
drained from each sump. The volume measured must satisfy the minimum capacity
requirements of paragraph AC 27.971b(1).

AC 27.971A.    § 27.971 (Amendment 27-23) FUEL TANK SUMP.

     a. Explanation. Amendment 27-23 prescribed minimum values for fuel tank sump
capacity, authorized the use of a sediment bowl in lieu of a sump, and required these
sumps or sediment bowls to be effective in any ground attitude which can reasonably be
expected in service.

     b. Procedures. The policy material pertaining to this section remains in effect.
Additionally, if the rotorcraft is equipped with a sediment bowl or chamber, the capacity
should be at least one ounce for every 20 gallons of fuel tank capacity. The sediment
bowl or chamber should be located so that water will drain from all parts of the tank to
the sediment bowl or chamber when the rotorcraft is in any allowable normal ground
attitude. Compliance with the minimum sump capacity or the sediment bowl or chamber
requirements may be shown by analysis, test, or a combination of both, depending upon
the complexity of the fuel system.

AC 27.973.  § 27.973 FUEL TANK FILLER CONNECTION.

     a. Explanation. Fuel tank filler connections must be designed so that no fuel can
enter into any part of the rotorcraft other than the fuel tank during fueling operations.
Spilled fuel must be considered as well as fuel entered into the fuel filler port.

     b. Procedures.

         (1) Each fuel filler opening must be identified with the markings and placards
required by § 27.1557.

         (2) Each filler cap should provide a fuel-tight seal for the main filler opening
unless the fuel tank is vented through a small opening in the filler cap.

         (3) Each fuel filling point should have a provision for electrically bonding the
rotorcraft to ground fueling equipment.

         (4) Compliance with the requirements of this paragraph can normally be
demonstrated by analysis and physical inspection of the fuel filler design. Testing is not
normally required.





Page E - 74

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →