Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
relieves complex design requirements where simpler designs have proven to be
satisfactory.
b. Procedures. There is no change to the suggested methods of compliance.
AC 27.971. § 27.971 FUEL TANK SUMP.
a. Explanation.
(1) Each fuel tank must be provided with a drainable sump which is located at
the lowest point in the tank with the rotorcraft in a normal ground attitude.
(2) The main fuel supply to any engine may not be drawn from the bottom of
any fuel sump.
(3) Each fuel sump drain must comply with the requirements of § 27.999.
b. Procedures.
(1) Each fuel sump should have an effective capacity which is not less than
0.25 percent of the tank capacity or 1/16 gallon, whichever is greater, with the rotorcraft
in any ground attitude to be expected in service. This sump capacity will provide a level
of safety equivalent with other normal category aircraft (reference § 23.971).
(2) Demonstration of compliance with the minimum sump capacity
requirements may be shown by analysis, test, or a combination of both depending on
the complexity of the fuel system design.
(3) If minimum sump capacity is to be demonstrated by test, the following
general test procedures will produce acceptable results:
(i) Determine the most critical ground attitude to be expected in service
from such considerations as uneven terrain, slope landing limits, etc. The critical
attitude for each tank will be that for which the maximum amount of fuel can be
withdrawn from the tank using the rotorcraft’s fuel supply system.
(ii) Using a rotorcraft with a fuel system which conforms to the final
design specification, position the rotorcraft to the critical attitude for the tank to be tested
using leveling jacks, actual terrain of a predetermined slope, or other similar means.
(iii) Using the rotorcraft’s fuel supply system, pump fuel from the tank
being tested until the supply system will no longer withdraw fuel. This can be done
without the rotorcraft engine actually running unless an engine driven pump is an
essential component of the fuel supply system. Caution should be exercised if an
engine is to be run to fuel exhaustion since engine surge at the pump cavitation point
can result in damaging torsional loads in the transmission drive system.
Page E - 73
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.