Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
order to avoid fluid loads in the bladder itself. The interior of the cavity should be
smooth to avoid damage to the bladder cells.
b. § 27.967(b):
(1) Explanation. This paragraph requires the design to provide ventilation and
drainage of spaces adjacent to fuel tanks to avoid accumulation of fuel or fumes to be
expected from minor leakage of fuel tanks. This is needed to minimize the possibility of
fire or explosion in these spaces. An exception to this requirement is allowed for
bladder cells installed in a closed compartment. For this configuration, ventilation may
be limited to that provided by compartment drains if the ventilation is adequate to
maintain proper pressure relationship between the bladder cell and cell compartment air
spaces.
(2) Procedures. With the assumption that fuel tank leakage will occur, require
the tank compartments to be provided with drains at any low point. These drains should
conduct fuel clear of the rotorcraft and should be three-eighths of an inch or larger in
diameter to minimize clogging. As with any drain intended to function in flight,
verification that reverse flow will not occur due to pressure differentials at each end of
the drain is appropriate. Ventilation for these tanks should involve openings in the
compartment such that in-flight slipstream and/or rotor downwash will rapidly and
continuously purge the tank compartment of fuel fumes. Openings should not be
located so the fumes or fuel can reenter the rotorcraft. For flexible tank liner
configurations (bladder cells), no specific ventilation is required if the cell is located in a
compartment which is closed, except for drain holes. Note that a cell leak may be
expected to produce fumes in the compartment airspace which are flammable; thus,
items installed in bladder tank cavities shall not create a hazard during either normal or
malfunction conditions. The vent system for the interior of the cell must be adequate to
ensure that the bladder cell interior pressure is always positive or at least neutral with
respect to any other airspace in the cell compartment to prevent collapse of the bladder
cell. Drainage of the cell compartment should meet the criteria discussed above.
(3) A light mesh or string network hung between the bladder cell and its
compartment walls is recommended to provide seepage channels to facilitate fuel
leakage to the low-point compartment drains.
c. § 27.967(c):
(1) Explanation. This paragraph requires a measure of protection for fuel tanks
from adverse effects of a fire in a fire zone.
(2) Procedures. Verify that a firewall meeting the requirements of § 27.1185
effectively separates any fuel tank from any engine. To minimize hazards of heat
transfer to a fuel tank through a fire wall during an engine compartment fire, verify that
at least one-half inch of clear airspace exists between the tank and the firewall.
Page E - 71
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.