FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-70

PDF page 488 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 488
AC 27-1B · E-70Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

tests in accordance with § 27.965(d). Using this basis, a 14- by 14-inch properly
constructed tank would not require vibration and slosh tests.

                   (ii)     If the tank construction is of a metal or integral design which can be
shown to be similar to previously approved tanks with acceptable service history, the
vibration and slosh tests may not be required. Similarity would entail comparing the
construction technique; i.e., similar panel size, similar sealing methods, skin and angle
thickness, loads being similar, etc.

                    (iii)   For fuel tanks located in the sponson or stub wing, the entire sponson
or wing should be rocked and vibrated unless it can be determined that a certain portion
of the tanks is critical. In this case a fixture should be developed such that the portion of
the tank being tested is rocked about a pivot point which would produce the same
amplitudes of motion for the portion of the tank being tested, as if the whole sponson or
wing was being tested. Structure loads in conjunction with these tests have not been
required.

               (iv)  The amplitude of vibration specified in the regulation is double
amplitude (peak to peak). Vibration amplitudes less than one thirty-second of an inch
must be justified by instrumented tests of the tank installed in the aircraft.

              (v)  The vibration and slosh procedures listed in Military Specification,
MIL-T-6396, have been accepted to show compliance with § 27.965(d).

         (3) After all tests have been conducted, the tanks should be leak checked using
test fluid conforming to Federal Specification TT-S-735 type III or equivalent.

AC 27.967.  § 27.967 FUEL TANK INSTALLATION.

     a. § 27.967(a):

         (1) Explanation. This paragraph was added by Amendment 27-30 to create
parallelism of both regulatory structure and level of safety between Parts 27 and 29 by
the Crash Resistant Fuel System final rule on October 3, 1994. This paragraph sets
forth a series of detail requirements for fuel tanks intended to ensure that tank leakage
or failure is unlikely. These regulatory requirements pertain primarily to proper support
of the tank and protection against chafing.

         (2) Procedures. For conventional metal tanks, the support devices, commonly
called “cradles,” should be designed with wide flanges or cap strips at the contact area
with the tank to distribute the loads in the tank material. To prevent chafing, install
nonmetallic padding, treated to eliminate absorption of fuel between the tank and the
support structure. Cork strips sealed with shellac and bonded to the support structure
have been found suitable. Fuel cell sealant material should be applied over rivet heads
and in corners. Bladder cells must be designed to fit accurately in the cell cavity in



Page E - 70

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →