FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-69

PDF page 487 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 487
AC 27-1B · E-69Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

detailed compliance procedures for § 27.952(h). The compliance procedures for
§ 27.952(h) also provide compliance for puncture resistance under § 27.963(g).

         (2) Paragraph (f).The procedures for old paragraph (f) still apply under new (f).
Compliance with the added crash resistance requirement of new (f) can be shown by
conducting a thorough design review of each fuel tank compartment to ensure that all
the regulatory criteria are met. (All fuel drains and vents should also be reviewed to
ensure that they meet applicable § 27.952 requirements.) A basic static loads analysis
followed by a stress analysis is typically used to determine that the enclosure protects
the fuel tank and provides the crash resistance level necessary for occupant survival in
an otherwise survivable impact. The applicable emergency load factors are typically
used to design the enclosure. (Section 27.952 contains the corresponding load factors
for fuel cells and their attachments.) The emergency load factors are typically adequate
for all loading conditions encountered by the enclosure in service. The typical design
approach is to design the enclosure to crush at a rate approximately the same as the
crush rate of the fuel tank and to ensure that all puncture hazards (such as sharp
projections either enhanced or created by impact that would penetrate the fuel tank) are
minimized in design. (See paragraph AC 27.952 guidance material for details.)

27.965.   § 27.965 (Amendment 27-12) FUEL TANK TESTS.

     a. Explanation. This regulation defines the tests that must be accomplished to
show compliance for rotorcraft fuel tanks.

         (1) Four basic types of fuel tanks are: (1) a metal tank installed in the aircraft or
at the wing tip; (2) an integral tank; (3) a nonmetallic self-supporting tank (fiberglass);
and (4) nonmetallic flexible bladder-type tanks.

         (2) There are two basic tests required by the regulations. One test procedure
substantiates the design by tests and analysis by applying applicable pressure to the
tank. The other procedure substantiates the design by vibration and slosh tests of the
tanks.

     b. Procedures.

         (1) Pressure Test. The 3.5 or 2.0 PSI pressure test listed in the regulations
should be conducted unless the pressure with a full tank for maximum limit acceleration
or emergency acceleration is greater. Section 27.337 gives the value for the limit
acceleration.

         (2) Vibration and Slosh Tests.

                  (i)   There is not an absolute value of what constitutes “large” unsupported
or unstiffened flat areas. However, it has generally been considered that any fuel tank
with less than 10 gallons capacity, constructed with simple, wide, flat geometric shape
and using metal (in metal tanks) of 0.05-inch thickness or greater would not require


                                                       Page E - 69

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →