Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
questionable, the slosh and vibration tests of § 27.965 may be accepted as
substantiation of this requirement.
(3) The fuel tank clearance required by paragraph (c) may be determined by
inspection of the design.
(4) The ventilation and interconnect requirements of paragraph (d) may usually
be determined by flight tests which explore maximum rates of climb and descent with
sensitive pressure measuring equipment installed inside tanks and in the ventilation
airspaces provided to comply with this rule.
AC 27.963A. § 27.963 (Amendment 27-23) FUEL TANKS: GENERAL.
a. Explanation. Amendment 27-23 added new subsections (e) and (f) that require
designs and tests to ensure that no exposed surface inside a fuel tank would, under
normal or malfunction conditions, constitute an ignition source. They also set forth
standards for the design and qualification of fuel tanks located in personnel
compartments. These requirements are needed to ensure freedom from the hazards of
fuel tank internal explosions and to ensure that fuel tanks, installed in passenger
compartments, present no hazards to the personnel or to the rotorcraft.
b. Procedures. Section 27.963(e) requires the temperature of any exposed
surface inside a fuel tank to be at least 50° F lower than the lowest auto-ignition
temperature of the fuel or fuel vapors in the tank (reference paragraph AC 27.1185b(3),
§ 27.1185). For compliance with § 27.963(e), the internal component surface
temperatures can be determined by flight or laboratory tests. The most critical flight
conditions are established with sensitive temperature and pressure measuring
equipment. This equipment is installed inside the tanks and in the ventilation air
spaces.
AC 27.963B. § 27.963 (Amendment 27-30) FUEL TANKS: GENERAL.
a. Explanation. Amendment 27-30 adds a new requirement to paragraph (g) that
(in addition to the current requirements) requires that the fuel tank bladder or liner be
puncture resistant by meeting the TSO C-80, paragraph 16.0, screwdriver test
requirements, using a new crash resistance based minimum puncture force of 370 lbs.
A new requirement is also added to paragraph (f). Paragraph (f) now additionally
requires that each fuel tank installed in a personnel compartment be crash resistant by
meeting the applicable criteria of the new Crash Resistant Fuel System requirements of
§ 29.952 (Re: paragraph AC 27.952).
b. Procedures.
(1) Paragraph (g). The procedures for old paragraph (g) still apply under new
(g). In addition, to comply with the added puncture resistance requirement under new
(g), the requirements of § 27.952(h) must be met. Paragraph AC 27.952 gives the
Page E - 68
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.