Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(8) Engine operation throughout the test should be normal; i.e., no surge, stall,
flameout, etc., and the engine fuel inlet requirements should not be exceeded.
(9) Alternative tests on appropriate test rigs may be conducted ensuring proper
simulation of altitude, ambient temperature, fuel temperature, fuel flow, and load factors.
AC 27.961A. § 27.961 (Amendment 27-23) FUEL SYSTEM HOT WEATHER
OPERATION.
a. Explanation. Amendment 27-23 simplifies and restates the fuel system hot
weather certification requirements and adds a requirement for the system to be capable
of providing adequate fuel during probable transients. These changes clarified the
existing wording to assure adequate qualification testing.
b. Procedures. This paragraph specifies that all suction lift systems and any other
fuel system that may be conducive to vapor formation show satisfactory engine fuel inlet
conditions (within criteria established by the engine manufacturer) when using the fuel
with the highest true vapor pressure (TVP) at 110° F fuel temperature. Engine
operating conditions should include those defined by §§ 27.927(b)(1) and 27.927(b)(2).
Compliance can be shown by analysis, testing, or a combination of both.
AC 27.963. § 27.963 FUEL TANKS: GENERAL.
a. Explanation.
(1) Paragraph (a) sets forth general requirements for fuel tank structural
aspects.
(2) Paragraph (b) requires design features to react forces to be expected from
fuel surging due to accelerations of the rotorcraft.
(3) Paragraph (c) requires design features to ensure heat transfer from an
engine compartment fire will not jeopardize the fuel tank integrity.
(4) Paragraph (d) requires design features to minimize the hazards of a leaking
fuel tank and also requires design features to ensure that unwanted transfer of fuel from
one tank to another does not occur due to differences of pressure in the tanks.
b. Procedures.
(1) For paragraph (a), the tests of § 27.965 are normally adequate if performed
in conjunction with the reliability test of § 21.35 or other service simulation tests.
(2) For paragraph (b), internal or external stiffening may be required for surge
resistance. If the analysis provided to show the adequacy of the surge resistance is
Page E - 67
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.