Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(i) There are high points in the fuel system which would allow
accumulation of vapor; or
(ii) The engine fuel inlet pressure is negative relative to tank pressure
because of low boost pump pressure or high fuel system pressure losses (but still within
fuel pressure limits).
(3) The requirement to use 110° F fuel is a carryover from the recodification of
CAR Part 6, although the use of hotter fuel would tend more toward vapor formation.
(4) The term “vapor lock” means a change in normal engine operation as a
result of the formation of fuel vapor-air mixtures in the fuel feed system.
b. Procedures.
(1) The fuel type to be used should be that with the highest true vapor pressure
(TVP) at the 110° F condition.
(2) The fuel should be heated as rapidly as possible since the longer fuel is
heated the more vaporization occurs resulting in unconservative test results.
(3) If the test is performed at cool ambients, the fuel lines, tanks, etc., may have
to be insulated to ensure that the fuel inlet temperature is approximately the same as
would be experienced on a hot day.
(4) The fuel level should be the lowest consistent with test safety.
(5) The flight tests to the service ceiling should include maximum power climbs
to selected intermediate altitudes where various maneuvers including the following are
performed:
(i) Low power descent with rapid transition to takeoff power.
(ii) Turns and cyclic pull-ups with load factors comparable to the flight
strain survey.
(iii) For multiengine rotorcraft with 30-minute and/or 2.5-minute OEI power
ratings, conduct a rapid single-engine acceleration from low power to engine topping
power followed by cruise at the maximum allowable OEI power.
(6) The flight test maneuvers should be repeated at the service ceiling.
(7) Except for transients and descents, the power available used should
correspond to a 100° F sea level day lapsed 3.6° F/1,000 foot pressure altitude.
Page E - 66
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.