FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-64

PDF page 482 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 482
AC 27-1B · E-64Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

the fuel flow required during the transient may exceed the fuel flow required for steady
state at the maximum power condition.

                   (ii)    In multiengine rotorcraft, a rapid acceleration to the maximum OEI
power rating that will be requested may be a critical condition. The fuel flow during the
transient may be higher than that required at the steady state OEI condition.

         (3) If auxiliary fuel pumps (boost pumps) are used to supply fuel to the engines,
and ejector pumps are used for cross-feed or other inter-tank fuel distribution systems,
a test should be run that will place the maximum fuel demand on the auxiliary pump(s).

         (4) In some multiengine rotorcraft, a single pump may be required to provide
fuel flow to all engines in the event of an auxiliary pump failure.  If this is the case, a test
should be conducted with a simulated (or actual) failed auxiliary pump.  If the functional
auxiliary pump is designed to provide motive flow for cross-feed systems, the most
critical condition of fuel flow demand should be tested.

         (5) Transient and steady state maneuver loads (g-loading) may affect the fuel
pressure at the engine to airframe interface. This effect should be considered and then
tested, if appropriate.

         (6) The methods of specifying the engine inlet fuel pressure requirements are
sometimes related to fuel temperature and altitude. Therefore, it is necessary to
explore the extremes of the envelope to assure compliance rather than attempting to
select one critical condition. For instance, the increase in fuel viscosity at cold
temperatures may increase system pressure drop and offset a slight drop in required
fuel flow. In this case, critical fuel inlet conditions may not be experienced at maximum
engine fuel flow.

         (7) A conservative demonstration would consider the maximum allowable fuel
viscosity in combination with the maximum fuel flow. Otherwise, several test points may
be required.

         (8) Fuel Transfer Systems. Section 27.955(b) specifies that if normal operation
of the rotorcraft fuel transfer system continually delivers fuel to an engine feed tank, and
maintains a specific fuel level in the feed tank, then the specified fuel level in the feed
tank should be maintained automatically during all flight or surface operating conditions
expected with the rotorcraft.

AC 27.959.  § 27.959 UNUSABLE FUEL SUPPLY.

     a. Explanation. This rule requires the applicant to establish a value for unusable
fuel for each tank. This value for unusable fuel may be selected by the applicant to
facilitate compliance with § 27.1337(b)(1) provided the amount is equal to or greater
than the actual unusable fuel. The actual unusable fuel is the amount of fuel in the tank



Page E - 64

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →