Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
Analytical methods that are used to adjust the test results should be verified with limited
testing. It should be shown during compliance testing that the fuel pressure, at the
engine to airframe interface, will be within the limits specified by the engine
manufacturer. The fuel pressure at this point should be maintained within limits
specified by the engine manufacturer during all critical maneuvers and accelerations.
All of the following conditions should be met during compliance testing unless it can be
shown that combinations of the conditions are not possible.
(i) The fuel quantity in the tank(s) in use during the test may not exceed
the unusable fuel quantity established under § 27.959, plus the minimum quantity
required to conduct the test.
(ii) During the compliance test, the rotorcraft should be maneuvered to
create the most critical fuel pressure head between the fuel tank outlet and the engine
to airframe interface (engine fuel inlet).
(iii) For boost pump fed systems, it should be determined which pump
(primary or secondary) would create the most critical restriction if it failed. The critical
pump should then be installed to create the critical restriction, either by actual or
simulated failure.
(iv) Various combinations of engine power demand, electrical power
available, and motive flow requirements for ejector pumps, will have an effect upon the
fuel flow and pressure available at the engine to airframe interface. Adequate fuel
pressure should be available to the engine with the most critical combination of these
parameters.
(v) Critical values of fuel properties that may adversely affect fuel flow
and/or fuel pressure should be applied. This includes alternate types of fuel if
certification with alternate fuels is requested. At the minimum, the fuel that will create
the highest vapor to liquid ratio should be used during hot fuel tests (§ 27.961). The
most viscous fuel should be used during cold fuel tests.
(vi) The fuel filter, required by § 27.997, should be partially blocked to
simulate the maximum contamination allowable. The blockage should be sufficient to
activate the impending bypass indicator that is required by § 27.1305(q).
(2) Unique Conditions. The phrase, “…Provide the engine with at least
100 percent of the fuel required under all operating and maneuvering conditions…”
(§ 27.955(a)), includes unique flight conditions within the operational envelope of the
rotorcraft. Critical conditions of fuel flow to the engine(s) may exist under the following
conditions (and others identified by the applicant); therefore, they should be evaluated
and tested if applicable:
(i) In a single engine rotorcraft, a rapid acceleration to maximum power
(torque) that will be requested for certification may be a critical condition. In this case
Page E - 63
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.