FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-60

PDF page 478 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 478
AC 27-1B · E-60Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


         (6) Adverse transient and steady-state maneuver loads should be considered
since the g-loading experienced may tend to decrease the fuel inlet pressure below
allowable limits.

         (7) In assuring adequate fuel flow at the necessary engine inlet pressure
(§ 27.955(a)(1)), both hot and cold fuel would normally be evaluated for the suction lift
system, whereas cold fuel is usually more critical for the boosted pressure system.

         (8) The method of specifying the fuel inlet pressure requirements varies with
the engine model. Some of these include:

                  (i)    Specification of a gage pressure as a function of altitude for suction
system operation. The particular fuel and fuel temperature for demonstrating the criteria
may be specified in the engine documents. Other approved fuels, fuel temperatures,
and boost-pump-on operation are considered satisfactory if the demonstration with the
specified fuel is successful.

                   (ii)   Specification of a maximum allowable vapor-to-liquid ratio for hot fuel,
and minimum absolute pressure as a function of altitude for cold fuels.

                    (iii)   Specification of a fuel inlet pressure relative to the true vapor pressure
of the fuel, in combination with a maximum allowable vapor-to-liquid ratio.

               (iv)   Specification of separate pressure limits for boost-on and suction lift
operation.
              (v)   Specification of special limits for emergency use or emergency fuels.

         (9) Because the various methods of specifying the engine inlet fuel pressure
requirements are sometimes related to fuel temperature and altitude, it is often
necessary to explore the extremes of the envelope to assure compliance rather than
attempting to select one critical condition. Additionally, the rapid increase in fuel
viscosity at colder temperatures, which tends to significantly increase system pressure
drop, can more than offset a slight drop in required fuel flow such that the critical fuel
inlet conditions may not be experienced at maximum engine fuel flow.
Figure AC 27.955–1 illustrates the point.





Page E - 60

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →