Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(ii) That the test be conducted with minimum fuel onboard, consistent
with test safety; and
(iii) That operation with both main and emergency pumps be considered.
(3) Section 27.955(b) specifies that if an engine can be supplied with fuel from
more than one tank, the fuel system must feed promptly when fuel becomes low in one
tank and another tank is selected.
b. Procedures.
(1) Testing (including bench tests) has been the accepted method to show
compliance with § 27.955(a). Analytical techniques may be used to adjust the system
test results to various fuel conditions and flows or to account for minor modifications to a
system. A purely analytical approach is not generally acceptable.
(2) Methods to adjust the test data for different fuel properties and flows should
be verified by limited testing.
(3) If a suction lift system is used and hot fuel verification is involved, testing is
appropriate.
(4) The proper interpretation of the phrase “100 percent of the fuel flow required
under the intended operating conditions and maneuvers” may include consideration of
acceleration fuel flow in addition to the steady-state fuel flow requirement.
(i) For example, if on a single-engine rotorcraft on a cold-day takeoff,
engine torque is the limiting parameter, the steady-state fuel flow demand
corresponding to that torque may be exceeded during engine acceleration in
maneuvers.
(ii) In addition to the consideration of acceleration fuel flow, good design
would include some margin to account for possible inadvertent overtorque.
(5) For multiengine rotorcraft, adequate fuel flow under OEI conditions should
be assured in the critical fuel system configuration.
(i) If on a multiengine rotorcraft, it is acceptable to operate following an
engine failure in more than one fuel system configuration (for example, if crossfeed is
an acceptable mode) then the supplying of two engines through common components
may be more critical than the OEI condition.
(ii) In verifying satisfactory fuel system operation for OEI conditions, the
fact that the remaining engine may go to the gas producer speed topping limit fuel flow
rather than to the steady-state OEI power value should be assessed.
Page E - 59
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.