FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-48

PDF page 466 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 466
AC 27-1B · E-48Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

             (xv)  Any shielding of electrical wires from abrasion, cutting, or
overextension must be nonconductive.

              (xvi)  All fuel line installations not containing breakaway couplings should be
reviewed to insure that they will not be overtensioned in a survivable impact, that they
are properly grouped and properly exit fuel tanks, firewalls, and bulkheads in the area of
least probable damage, and that their number and lengths are safely minimized.

               (xvii) Crash resistance guidance for other basic components is contained in
related AC paragraphs such as paragraphs AC 27.963 (§ 27.963, bladders and liners),
AC 27.973 (§ 27.973, fuel tank filler connections) and AC 27.975 (§ 27.975, fuel tank
vents).

        (18) Section 27.952(g) requires rigid or semirigid fuel tank or bladder walls of
any material construction to be both impact and tear resistant. This minimizes a PCF
from impact-induced rupture and tear.

                  (i)   A rigid tank or bladder can resist fluid pressure loads as a flat plate in
bending. A semirigid tank can resist fluid pressure loads partially as a flat plate in
bending and partially as a membrane in tension. Flexible liners are exempt from the
requirements of § 27.952(g) since an unsupported flexible liner can resist only pure
tension loads acting as a membrane (i.e., it has negligible bending strength). The rigid
shell structure required by § 27.967(a)(3) that surrounds the flexible liner (membrane)
carries the crash-induced impact and tear loads; whereas, the flexible liner is only
significantly loaded in tension if the shell structure is penetrated by a sharp object on
impact.

                   (ii)   For metallic tanks, rigid or semirigid composite tanks (resin matrix),
semirigid bladder designs (rubber matrix), metal-composite hybrid designs, and all other
tank designs, impact and tear resistance should be shown by analysis and tests.

                    (iii)  Designs using resin matrix composites should be subjected to the
composite structure substantiation guidance of AC 20-107A, Composite Aircraft
Structure, dated April 25, 1984, and paragraph AC 27 MG 8. Designs using rubber
matrix composites are subject to the standard substantiation requirements for these
devices, such as TSO-C80.

               (iv)  One set of crash resistance tests that constitutes an acceptable
method of substantiation to the requirements of § 27.952(g) for all tank designs
regardless of the materials used are those specified in Paragraphs 4.6.5.1 (Constant
Rate Tear); 4.6.5.2 (Impact Penetration); 4.6.5.3 (Impact Tear); 4.6.5.4 (Panel Strength
Calibration); and 4.6.5.5 (Fitting Strength) of MIL-T-27422B, “Military Specification;
Tank, Fuel, Crash-Resistant Aircraft.” These test requirements, or equivalent means,
should be applied for and discussed early in certification.  If the MIL-T-27422B tests are
selected, severity differences between military combat requirements and the civil



Page E - 48

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →