FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-49

PDF page 467 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 467
AC 27-1B · E-49Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

environment should be accounted for by reducing the MIL-T-27422B requirements, as
follows:

              (A) Constant Rate Tear. The minimum energy for complete separation
should be 200 foot-pounds (reference 4.6.5.1).

              (B) Impact Penetration. The drop height of a 5-pound chisel should be
reduced to 8.0 feet (reference 4.6.5.2).

             (C) Impact Tear. The drop height of a 5-pound chisel should be reduced
to 8.0 feet and the average tear criteria should not exceed 1.0 inch (reference 4.6.5.3).

        (19) Section 27.952(g) also requires that all fuel tank designs (regardless of the
materials utilized and whether or not a flexible liner of any type is used) for each tank or
the most critical tank be analyzed and tested to the criteria of paragraph (18)(iv) of
§ 27.952, or equivalent.

        (20) Any type of flexible liner or bladder used in any type of fuel tank
construction (integral, hard shell, etc.) must meet the strength and puncture resistance
requirements of § 27.963(g). Section 27.963(g) contains the new puncture resistance
requirement for flexible liners and other liner material certification requirements.
Unlined, bladderless fuel tanks are also required to meet this requirement. Most
unlined, rigid fuel cell designs should readily exceed the 370-pound minimum puncture
force requirement because of overriding design requirements and material
characteristics, such as stiffness and ductility.

NOTE: TSO-C80, “Flexible Fuel and Oil Cell Material,” is referenced in the advisory
material for § 27.963(g) and contains the detailed qualification requirements for these
materials. The current puncture resistance test of TSO-C80, paragraph 16.0, states
that the force required to puncture the bladder material must be greater than or equal to
15 pounds (e.g., screwdriver test). Section 27.963(g) has increased the TSO
paragraph 16.0 puncture force value to be greater than or equal to 370 pounds. This is
for fuel cell bladder or liner material only. Oil cell material puncture force requirements
are not changed.

         e. Typical Examples of Loading Modes and Test Setups for CRFS
Components. The following figures, which are referred to periodically in the advisory
circular, show typical examples of test setups for CRFS components such as
breakaway fuel fittings, hoses, hose end fittings, and hose assemblies.





                                                       Page E - 49

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →