FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-47

PDF page 465 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 465
AC 27-1B · E-47Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

               (vi)  Fuel and electrical lines and components running through hazardous
areas or directly through structure, such as a bulkhead, should be locally separated and
protected from over-extension, severe abrasion and guillotine cutting by frangible
panels, suitable clearance, rubber grommets, braided armor shielding (which should be
nonconductive for electrical lines), or other equivalent means.

                (vii)  Fuel lines routed directly to instruments, transducers, or other
equivalent devices should be crash resistant, in accordance with § 27.1337(a)(2), to
minimize leakage in case of line rupture induced during a survivable impact.

                 (viii)  Electrical wires routed directly into electrical boxes or instruments
should be designed with sufficient local slack and locally routed in the least probable
damage direction and zone, or otherwise protected to minimize the probability of
damage-induced arcing.

               (ix)  Fuel lines routed directly into fuel tanks or other fuel system
components should be locally routed in the least probable damage direction and zone,
or otherwise protected, to minimize the probability of damage-induced fuel leaks.

              (x)   Fuel pumps mounted inside fuel tanks should be rigidly attached to
the fuel tank only.  If the pump is airframe mounted and has structural significance, it
should have a frangible or deformable attachment (reference paragraph
AC 27.952d(12)). Electrical boost pumps, if used, should be installed with a minimum of
6 inches of slack wire at the pump connection. The pump wires should be shrouded to
prevent cutting in a survivable impact. Nonsparking, breakaway wire disconnects or
other equivalent means may be used in lieu of the 6 inches of slack wire.

               (xi)  Fuel filters and strainers, to the maximum practicable extent, should
not be located in or adjacent to the engine intake or exhausts and should retain the
smallest practicable quantity of fuel.

                (xii)  The number of fuel valves should be kept to a minimum.  If electrically
operated valves are used, they should be installed with a minimum of 6 inches of slack
in the electrical lines, unless protected by equivalent mean (reference 17(i)). The valves
should be installed with the maximum amount of protection and separation of the
electrical wires from the remainder of the valve assembly.

                 (xiii)  Fuel quantity indicators mounted in or on fuel tanks should be
selected, designed, and installed to provide the minimum puncture or tear hazard to the
fuel tank in a survivable impact.

              (xiv) Fuel tank and bladder enclosures should have smooth, regular
shapes that avoid sharp edges and corners. Minimum concave and convex radius
design criteria should be developed and adhered to. Magnesium should not be used in
fuel cells, and any cadmium-plated parts should not be exposed to fuel.



                                                       Page E - 47

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →