FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-46

PDF page 464 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 464
AC 27-1B · E-46Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

tearout and leakage. The number of drains should be minimized by design techniques
such as those that avoid low points in the lines. Drain lines should be made of ductile
materials or otherwise designed to provide impact tolerance. Drain line connections,
fittings, and other components should be designed to meet the fatigue requirements of
§ 27.571 and 27.952(d)(3). This ensures that unintended partial or full fatigue failures
do not occur in normal operations that, if undetected, could compromise the CRFS’s
intended level-of-safety for the mitigation of post crash fire in a survivable impact. Drain
valves should be designed to have positive locking provisions in the closed position in
accordance with § 27.999(b)(2).

        (17) Section 27.952(f) specifies that fuel tanks, fuel lines, electrical wires, and
electrical devices must be designed and constructed, as far as practicable, to be crash
resistant. Typical mechanical design criteria necessary to minimize fuel spillage
sources, ignition sources, and their mutual contact in a survivable impact (i.e., provide
crash resistance) are stated by the following subparagraphs. These mechanical design
criteria should be incorporated in each design to the maximum practicable extent.
Compliance is accomplished and assessed by a thorough design review and potential
PCF hazard analysis with findings and solutions that are documented and approved.
Any additional PCF hazards that are identified should be documented, included,
addressed equally, and eliminated to the maximum practicable extent. Engineering
evaluation, analysis, and tests are all required to determine the maximum level of
practicability.

                  (i)   They should not initiate or contribute to a post crash fire in an
otherwise survivable impact. A hazard analysis should show which components are
critical in this regard and should be assessed in detail for hazard elimination purposes.

                   (ii)   Fuel and electrical lines and components should be located away from
each other, away from probable crash impact areas, and away from areas where
structural deformation or large objects (such as engines or transmissions) may, by
crushing or penetration, cause fuel spillage or create an electrical ignition source, or
both.

                    (iii)   Fuel and electrical lines and components should be located separately
and away from areas where impact and severing by rotor blades during a survivable
impact are probable.

               (iv)  Fuel and electrical lines and components should be in no danger of
being punctured or severed during a survivable impact by locally stiff vertical
understructure such as a collapsed landing gear strut.

              (v)   Fuel and electrical lines and components should be routed separately
in areas of maximum protection, such as along heavier structural members, and away
from areas where significant damage is probable.




Page E - 46

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →