FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-44

PDF page 462 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 462
AC 27-1B · E-44Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

              (B) Fuel lines should not be located in any occupiable area unless they
are shrouded or otherwise designed to prevent spillage and subsequent ignition during
and immediately following a survivable impact.

             (C) Fuel tanks should not be located in or immediately adjacent to engine
compartments, engine induction or exhaust areas, heaters, bleed air ducts, hot
air-conditioning ducts, or any other hot surface.

             (D) Fuel lines should be kept to a minimum in the engine compartment.
Fluid lines should not be located immediately adjacent to engine exhaust areas,
heaters, bleed air ducts, hot air-conditioning ducts, or any other hot surface.

              (E) Fuel lines should not be located where they can readily spill, spray, or
mist onto hot surfaces or into engine induction or exhaust areas. These locations
should be determined for each aircraft design by considering probable structural
deformation hazards in relation to the fuel system.

                   (ii)    Electrical ignition sources.

              (A) Fuel tanks and lines should not be located in electrical compartments.

              (B) Electrical components and wiring should be separated from fuel lines
and vent openings and kept to a minimum in fuel areas.

             (C) Electrical wiring should be hermetically sealed and equipment should
be explosion-proofed in areas where they are immersed in or otherwise directly
subjected to fuel and vapors and should meet § 27.1309 or should otherwise be
protected such that ignition is extremely improbable.

             (D) Electrical sensor lines that penetrate fuel tank walls should be
protected from abrasion or guillotine cutting during a survivable impact by use of potting,
rubber plugs or grommets, or other equivalent means and should be designed with
sufficient local slack, or equivalent means, to prevent both the wires and their protective
mountings from being cut by or torn from fuel tank walls by local deformation.

              (E) Electrical wires should be designed with sufficient slack or equivalent
means to accommodate structural deformation without creating an ignition source.

              (F) Electrical wires that could be subjected to severe local abrasion,
cutting, or other damage during a survivable impact should be protected locally by
nonconductive shields or shrouds.

            (G) Electrical wires that are not sufficiently separated from heat or ignition
sources to avoid potential contact during a survivable impact should be locally shrouded
with a nonconductive fireproof shroud.



Page E - 44

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →