Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(13) Section 27.952(d)(1) defines the impact design load conditions necessary
to deform a deformable attachment or to separate a frangible attachment. These loads
should be determined from analysis and/or test (reference paragraph d(14)), and
verified during certification. All impact loading modes (tension, bending, compression,
shear, and a combination) should be analyzed and the minimum critical frangible or
deformable design load determined, based on the ultimate strength of the attachment’s
weakest component. The critical load should be compared to the normal service loads
calculated and measured at the attachment’s location to insure unintended service
failures do not occur. (Normally, this criterion is readily satisfied because working loads
are much less than impact loads.) A fatigue check should be conducted to ensure that
the attachments meet the requirements of § 27.571. Typically, this can be
accomplished using the simplified method of AC 27 MG 11, paragraph e(2)(i),because
of the low ratio of working-load-to-crash-induced failure load. However, because of
service history, all fatigue sources (especially high cycle vibratory sources) should be
reviewed. The standard method of compliance with § 27.571 used for rotor system
parts may not be necessary to meet § 27.952(d)(3). An S-N curve may not need to be
generated using full-scale specimen fatigue tests, if the conservative method of AC 27
MG 11, paragraph e(2)(i),can be applied successfully. Fracture critical materials should
be avoided and ductile, damage tolerant materials utilized. Phased inspections to
ensure continued airworthiness should be considered. Special inspections after severe
maneuvers or hard landings should be required. A breakaway or deformation load less
than 300 pounds (based on maintenance considerations) is not permitted. If airframe
deformation due to flight loads is significant, its effect should be checked to ensure that
a static failure or low cycle fatigue failure does not occur. Large flight load deflections
are not usually present in rotorcraft.
(14) Section 27.952(d)(2) requires a frangible or locally deformable attachment
to function when the minimum breakaway or deformation load
(reference § 27.952(d)(1)) is met or exceeded in a survivable impact. The minimum
breakaway or deformation load is the load that either breaks or deforms each of the
frangible or deformable attachment(s) of each fuel cell, fuel line, or other critical fuel
system component to the airframe. Each breakaway/deformation load must be between
25 percent to 50 percent of the load which would cause failure (i.e., impact induced
tearout and subsequent fuel leakage) of the attachment to fuel cell, fuel line, or other
critical component interface. This is necessary in some installations to prevent tearout
of the structural attachment from the fuel cell component to which it is attached and the
resultant fuel leakage in a survivable impact. The primary loading modes (each of
which will produce a breakaway or deformation load) must all be considered to
determine the minimum load. This is done by analyzing the surrounding structure
(reference paragraph d(13)) to determine the three most probable impact failure forces
and their directions. The attachment should then be tested to insure it breaks or
deforms at the lowest ultimate crash (impact) load as long as the minimum working load
criterion of § 27.952(d)(1) is also satisfied. It should be noted that the ratio of the
ultimate failure load of the weakest component in the frangible or deformable
component’s load path and the normal service load (i.e., peak load or approved clipped
peak load experienced during a typical flight) of that component should be as high as
Page E - 42
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.