Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
failure in the critical loading mode and the results averaged. [For standard specification
(i.e., “off the shelf”) hardware, equivalent testing may have already been accomplished
and, if no other mitigating circumstances in the design and installation exist, need not be
repeated.] The average value is then used to size the equivalent device. Each
equivalent device must meet the fatigue requirements of § 27.571 to prevent
fatigue-induced leakage. Equivalent devices should be statically and dynamically tested
in an identical manner (where feasible) to breakaway couplings (reference
paragraph d(6)). All fuel hoses and hose assemblies (whether or not they are used in
lieu of breakaway fittings) should meet the following (reference MIL-STD-1290) or
equivalent requirements. Any stretchable hoses used as equivalent devices should be
able to elongate a minimum of 20 percent without leaking fuel. All other hoses used as
equivalent devices should have a minimum of 20-30 percent slack. It should be noted
that the ratio of the ultimate failure load of the weakest component in the fuel line and
the normal service load (i.e., the peak or approved clipped peak load experienced
during a typical flight) of that component should be as high as possible and still meet the
other load criteria of this section. Typically, this ratio should not be less than 5.
(i) All hose assemblies should meet or exceed the cut resistance, tensile
strength, and hose-fitting pullout strength criteria of MIL-H-25579 (USAF), MIL-H-38360,
or equivalent standards.
(ii) Hoses should neither pull out of their end fittings nor should the end
fittings break at less than the minimum loads shown in figure AC 27.952-3 when the
assemblies are tested as described in d(11)(iii) below. In addition to the strength
requirements, the hose assemblies should be capable of elongating to a minimum of 20
to 30 percent by stretch, slack, or a combination without fluid spillage.
(iii) Hose assemblies should be subjected to pure tension loads and to
loads applied at a 90° angle to the longitudinal axis of the end fitting, as shown in
figure AC 27.952-2. Loads should be applied at a constant rate not exceeding
20 inches per minute.
(12) Section 27.952(d) requires frangible or deformable structural attachments
to be used to install fuel tanks and other major system components to each other and to
the airframe when crash-induced hazardous relative motion could cause local rupture
and tearout of the component, spill fuel to an ignition source, and create a PCF. If it can
be conclusively determined that the probability of fuel spillage is 1 x 10-9 or less, no
further action is required. Typically, frangible designs are much easier to certify than
deformable designs because the scatter in failure loads is much less. Also, some
standard frangible military hardware (e.g., frangible bolts) is readily available. This is
not so for deformable designs. Each frangible or deformable structural attachment and
its installation should be reviewed to insure that, after an impact failure (i.e., separation
or deformation), it does not become a puncture or tear-out hazard and cause fuel
spillage.
Page E - 41
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.