FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-40

PDF page 458 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 458
AC 27-1B · E-40Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

open during normal operations. Visual means (such as, an axial misalignment between
the two coupling halves, a designed-in visual indicator, a combination or other
acceptable criteria) should be considered and specified in the maintenance manual
rejection criteria for operational inspections. Inspectability and phased inspection
requirements should be evaluated. Special inspections after severe maneuvers or hard
landings should be required.

         (8) Section 27.952(c)(1)(iv) requires breakaway couplings to have design
provisions that prevent uncoupling or unintended closing by operational shocks,
vibrations, or accelerations. These provisions depend on both the coupling’s design
and installation location. The structural environment should be defined, analyzed, and
compared with coupling specifications and certification data so that inadvertent
decoupling or closing does not occur. A phased inspection requirement should be
considered.

         (9) Section 27.952(c)(1)(v) requires a coupling design to not release more than
its entrapped fuel quantity when the coupling has separated and each end is sealed off.
The entrapped fuel is determined by the coupling design and is essentially the fuel
trapped between the seals when separation occurs (see breakaway coupling definition).
This is usually less than 8 ounces of fuel per coupling. Most coupling designs will leak
slightly after separation. This is acceptable but the leak rate should be 5 drops per
minute, or less, per coupling half. Specifications defining the entrapped volume of fuel
should be approved.  If the coupling is not approved or manufactured to an acceptable
military or civil specification, the qualification testing of d(6) should be conducted.

        (10) Section 27.952(c)(2) requires that each breakaway coupling or equivalent
device either in a single fuel feed line or a complex fuel feed system (e.g. a multiple
feed line or multitank cross feed system) be designed, tested, installed, inspected,
maintained, or a combination, so that the probability of inadvertent fuel shutoff in flight is
1 x 10-5, or less, as required by § 27.955(a). This should be determined by reliability
and failure analysis, other analysis, tests, or a combination and should be documented
and approved. Continued airworthiness should be ensured by phased inspections,
specific component replacement schedules, or a combination. This section also
requires each coupling or equivalent device to meet the fatigue requirements of
§ 27.571 to prevent leakage. (See the fatigue discussion in paragraph d(5).) The
typical method of compliance with § 27.571 used for rotor system parts may not be
necessary to meet § 27.952(c)(2). An S-N curve may not need to be generated using
full-scale specimen fatigue tests if the conservative method of paragraph e(2)(i) of
AC 27 MG 11, “Fatigue Evaluation of Rotorcraft Structure” can be applied successfully.

        (11) Section 27.952(c)(3) requires that an equivalent device, used instead of a
breakaway coupling, not produce a load, during or after a survivable impact, on the fuel
line to which it attaches greater than 25-50 percent of the ultimate load (strength) of the
line’s weakest component. This minimizes crash-induced fuel spills that may cause a
PCF. The ultimate strength of the weakest component should be determined by
analysis and/or tests. At least three specimens of the component should be tested to


Page E - 40

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →