Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(6) Drip Fence. A physical barrier that interrupts liquid flow on the underside of
a surface, such as a fuel cell, and allows it to drip nonhazardously to an external drain.
(7) Flow Diverter. A physical barrier that interrupts or diverts the flow of a
liquid.
(8) Frangible Attachment or Fitting. An attachment or fitting containing a part
that is designed and constructed to fail at a predetermined location and load.
(9) Deformable Attachment or Fitting. An attachment or fitting containing a part
that is designed and constructed to deform at a predetermined location and load to a
predetermined final configuration.
(10) Self-Sealing Breakaway Fuel Fitting. A fuel-carrying in-line,
line-to-firewall, bulkhead or line-to-tank connection that breaks in half and self-seals
when subjected to forces greater than or equal to the unit’s design breakaway force.
Each half self-seals using a spring-loaded valve (e.g., trap door or equivalent means)
that is normally open but is released and closed upon fitting separation. Fitting
breakaway force is typically controlled by a frangible metal ring (or series of
circumferential tabs) that connects the two fitting halves. Normal, fuel-tight integrity is
maintained by “O” rings held under pressure by the rigid, frangible connecting ring (or
tabs). When broken open, a small amount of fuel (usually less than 8 ounces) is
released. This is the fuel trapped in the coupling space between the two spring-loaded
valves. Once failed each coupling half may leak slightly. Typically, this leak rate should
be less than 5 drops per minute per coupling half.
(11) Crash Resistant Flexible Fuel Cell Bladder. Flexible, rubberized material,
usually with fibers (i.e., rubber “resin” and natural or synthetic fiber) in both the 0° (warp)
and 90° (fill) directions that is used as a liner in a rigid shell or integral tank. The
material acts as a membrane because, when unsupported, it can only carry pure
tension loads. Therefore, it must be uniformly supported by rigid structure
(reference § 27.967) so that the liner carries only compressive fluid loads and the
surrounding shell structure carries the fluid-induced shear, tension, and bending loads
transmitted through the liner or bladder. The material is usually secured (e.g., laced,
snapped, etc.) into its surrounding structure at key locations to maintain its intended
conformal shape. In many designs, lightweight spacers, such as structural foam, are
used between the liner and the airframe to maintain the liners intended conformal shape
and to transmit fluid loads to the airframe. The material is either qualified under
TSO-C80, “Flexible Fuel and Oil Cell Material,” or qualified during certification.
Sections 27.952 and 27.963(g) have increased the minimum puncture resistance
qualification requirement for liner material (see TSO-C80, paragraph 16.0) from 15 to
370 pounds.
Page E - 34
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.