Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(3) Paragraph (c) provides for sustained satisfactory operation of the fuel
system, with initially ice-contaminated fuel. Since ice in the fuel system is not
considered to be an emergency condition, but rather is an expected service encounter,
compliance would not involve the imposition of special rotorcraft limitations. Flight
manual instructions such as land as soon as practicable, reduce altitude to some value
less than otherwise permitted, reduce power, turn on boost pumps, etc., are not
appropriate in demonstrating compliance. Some methods of fuel system ice protection
which have been used to show compliance follow.
(i) Fuel heater. Usually these devices are fuel-to-engine oil heat
exchangers and are normally located to protect the fuel filter from blockage by ice in the
fuel. The adequacy of these devices should be established. Usually this involves
generation of a heat balance between heat gained by fuel and heat lost by oil using
performance data provided by the manufacturers of the fuel-oil heater, the oil cooler, the
heat rejected by the engine to the oil, etc. A minimum oil temperature associated with
the adequacy of the fuel heater may need to be established, marked on the oil
temperature gauge, and verified to be maintained during critical flight conditions. Other
unprotected parts of the fuel system remain to be evaluated and substantiated for
compliance with this requirement.
(ii) Oversized fuel filter. This method may only substantiate the fuel filter
and, as with the fuel heater method, is incomplete without evaluation of the remainder of
the fuel system. An icing test of the filter should be accomplished. Fuel preparation
procedures and method of testing should follow the applicable portion of SAE
Aerospace Recommended Practice (ARP) No. 1401. A satisfactory configuration is
achieved when a filter is demonstrated to have the capacity to continue to provide the
filtration function, without bypassing, when subjected to fuel contaminated by ice to the
degree required by this rule. Usually, a delta pressure caution signal for the filter is
needed to alert the flight crew that progressive filter blockage is in progress. The
caution device setting should be established by test which demonstrates that after
illumination of the caution signal sufficient filter capacity exists to enable completion of
the flight. Fuel pressure should not fall below established limits because of ice
accumulation on the filter.
(iii) Anti-ice additives. This method utilizes the properties of ethylene
glycol to reduce the freezing temperature of water in the fuel. It has the advantage over
other methods of protecting all components in the fuel system from ice blockage.
Compliance with the rule by this method involves the following.
(A) Eligible additives. PFA-55MB (Phillips Petroleum Co.) and additives
per specification MIL-I-27868, Revision D, or earlier. Later versions of this specification
do not require glycerin, which may be needed to protect fuel tank coatings.
(B) Compatibility. Both engine fuel system and aircraft fuel system should
be verified to be chemically compatible with the additive at the maximum concentration
to be expected in the fuel system. Usually, information on eligible system materials can
Page E - 30
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.