Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
evaluate the test results or publish acceptance criteria. A wave analysis may be
involved in identifying higher order excitations. Engine exhaust ducts which include
bends, noise suppressors, or other obstructions may require an evaluation similar to
that discussed above for the engine inlet. The engine manufacturer should be
consulted for instructions or approval of this aspect. High performance engines may
also require an engine inlet temperature survey. Details of instrumentation and
acceptance criteria should be provided by the engine manufacturer. Engines equipped
with only centrifugal compressors are less likely to encounter frequency coupling and
may not require this investigation. The engine manufacturer’s recommendations should
be followed in these cases.
(3) Torsional Stability.
(i) Explanation. Governor-controlled engines installed in rotorcraft are subject
to a fuel control resonant feedback condition which could be divergent if not properly
designed or compensated. This condition occurs when the response frequency of the
governor on the engine is coincident with or close to a low order natural torsional
frequency of the rotorcraft rotor drive system. Typically, these frequencies appear in the
3 to 5 CPS range. The manufacturer usually resolves torsional instability problems by
introducing damping into the engine governor or fuel control. Provisions for this change
must be supplied by or approved by the engine manufacturer. The final configuration
may be a compromise between a lightly damped control, which will allow a positive but
slow convergence of drive system torsional oscillations, and a highly damped control
which exhibits excessive rotor speed droop or overspeed following rotorcraft collective
control displacement.
(ii) Procedure. A ground and flight test program should be devised to evaluate
the torsional response of the engine and drive system combination presented by the
applicant. Instrumentation to record drive system torsionals should be applied to all
major branches of the drive system. Engine parameters such as torque and power
turbine speed should be recorded simultaneously with drive system parameters. The
test program should include ground tie-down operation and flight operation across a
range of engine power and rotor speeds while injecting control inputs as close to the
first order drive system natural frequency as possible. Mechanical methods of making
these inputs are not usually necessary if the desired frequency is in the 3 to 5 CPS
range and the instrumentation readout confirms that the drive system was actually
excited torsionally at its natural frequency. Control inputs should include collective,
antitorque, and throttle. Also, cyclic inputs may be important on tandem rotor rotorcraft.
The acceptance criteria may be dependent on several items. Among these are rotor
and drive system fatigue loading, engine power response characteristics, limitations
established by the engine manufacturer, etc. The acceptance criteria are usually stated
as a percent damping (minimum). Typically, 1 percent of critical equivalent viscous
damping (or greater) is acceptable. In effect, this means that the free vibration
response to a control input damps to ½ amplitude in 11 cycles or less.
Page E – 28
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.