FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 444

PDF page 444 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 444
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


           (A) Level flight with or without sideslip at different power settings.

           (B) Pull up or in turn.

          (C) Autorotation.

          (D) Descent at different rates.

             (ii) The maneuvers described in paragraphs b.(1)(ii)(A)(4)(i)(A) through (D)
above check the engine susceptibility to air flow distortions. The test technique involves
oscillations of the collective at various rates around the identified thresholds of the
compressor control bleed valves.

   (B) Degraded modes: Governor failures.

      (1) The specific degraded mode testing for a hydromechanically controlled engine
is different than for a digitally controlled engine. However, the basic principles for both
types of engine controls include:

            (i) Review of the safety analysis, especially the FMEA.

             (ii) Determine the failures to be checked in flight, based on prior analysis or
testing.

              (iii) For each failure to be checked in flight:

           (A) Evaluate the behavior of the engine when the failure occurs.

           (B) Determine the acceptability of the procedure of identification of the
degraded engine.

          (C) Assess the human factor aspects of the machine interface (cautions,
warning, etc.).

          (D) During the use of the degraded engine, consider the workload impact
related to engine response in adjusting NR or power for approach and landing.

           (E) Evaluate the adequacy of the RFM procedures.

      (2) Helicopters equipped with FADECs are becoming increasingly integrated into
the helicopter systems for engine control sensor inputs. For example, N2/NR values
available could depend on parameters such as airspeed, altitude, or temperature as
provided by the basic helicopter systems and sent to the FADEC. A




Page E – 26.4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →