Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
should be reduced when altitude increases) and the rotorcraft category (speed of
collective input should be reduced when rotorcraft max weight increases), the duration
of the maneuver should be from 1 to 3 seconds at low altitude to approximately 3 to 5
seconds at higher altitude.
(C) Some collective inputs should be made from desynchronized conditions (NR
> N2) but should be carefully done as those maneuvers generally lead to larger
reductions of NR and high free wheel or engine constraints.
(D) On multi-engine helicopters, collective inputs at lower speeds should be
done with one engine at idle position to check the behavior of the other engines in case
of an engine failure.
(E) Droop of N2/NR out of the green arc is permitted during the test, provided it
is acceptable to the engine or airframe manufacturer for the purpose of the test. The
goal is to check for generally satisfactory acceleration (no surge, no extreme N2/NR
droop, no significant overshoot). Any N2/NR droop must not result in a condition that
requires exceptional piloting skill, alertness, or strength to maintain safe flight.
(F) During those collective inputs, NR below the minimum NR should be avoided
by lowering the collective. The reasons for poor engine acceleration should be
determined.
(ii) Collective decrease inputs.
(A) Collective decrease inputs will verify:
(a) Combustion stability (i.e., that there is no flame-out).
(b) The engine behavior in transients and in particular the maximum free
turbine speed, minimum oil pressure, etc.
(c) The rotorcraft handling qualities (variation of pitch and roll and yaw, cross
coupling, etc.) during the transients.
(B) Rate of collective lowering should be built up from 5 seconds down to under
3 seconds. Regarding N2 overspeed, a quick stop type maneuver that leads to an initial
acceleration of the NR should be envisaged.
(4) Compressor stall investigation.
(i) The turbine engine installation should not suffer from compressor stalls
anywhere in the flight envelope. Previous tests as described above include some of the
required areas, but additional testing is necessary. In stabilized conditions, the
collective pitch is moved in slow and small oscillations in:
Page E – 26.3
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.