FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-23

PDF page 437 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 437
AC 27-1B · E-23Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (1) Subcritical Shafting Designs. Three basic methods of qualification may be
considered, with the required margins relative to the degree of assurance provided.
The margins are shown for guidance only.

                  (i)    Analytical.

              (A) Simplistic model(s) as shown in figures AC 27.931-1 and
AC 27.931-2; 35-percent margin shown above maximum operating speed.

              (B) Detailed model, taking into account significant variations in shaft
stiffness, mass distribution, cone adapters, support bearing stiffnesses, support
structure; 20-percent margin shown above maximum operating speed.

                   (ii)   Analytical supported by tests. Analysis supported by shake test
(rotating or nonrotating) or by bench test, where appropriate adjustments are made for
differences between the bench and the aircraft; 15-percent margin shown above
maximum operating speed.

                    (iii)   Whirl test on the aircraft.

              (A) For all cases, it should be shown that, under maximum permissible
unbalance and at the maximum operating speed, the shafting and support structure has
acceptable clearance and does not have excessive vibration.

              (B) For compliant pylon mountings, damping of the rigid body rocking
modes, which are often transitioned during runup to normal speed (and which are not
critical flexing modes), may be verified by analyses, laboratory tests, or ground runup
with the rotor at maximum permissible unbalance. Damping on the order of 5 percent
equivalent viscous damping is generally acceptable.

             (C) For tail rotor masts, the analysis should include fixed system structural
response including tailboom, fixed control surfaces, and vertical fin. The frequency
analysis will then contain both fixed system and rotating system modes. An energy
analysis can then be used to identify whether the modes are predominantly fixed
system or rotating system modes. Systems with up to 35-percent energy in the rotating
system have been operated in the field without significant problems. For this type of
shafting installation, it is advisable to avoid fixed system modes at multiples of shaft
speed, particularly where highly non-isotropic mountings exist.

         (2) Supercritical Shafting Design. Another facet occasionally encountered with
shafting is the concept of normally operating at speeds above the critical speed,
commonly referred to as “supercritical operation.” To function properly, suitable
dampers must be installed to enable the shaft to pass safely through the lower critical
speed up to the operating speed, and speed controls should be devised to avoid any
tendency to operate continuously at any critical speed. Accurate balancing of the
rotating components will also decrease the energy to be dissipated into the damping


                                                       Page E - 23

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →