FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-22

PDF page 436 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 436
AC 27-1B · E-22Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

transition through the critical speed range and to avoid excessive nonsyncronous
vibrations or instability when transitioning through the critical speed.

         (3) A review of typical design practices and drive system arrangements
discloses several types of shaft support and loading:

                  (i)   Main rotor/mast/transmission assemblies rigidly mounted to the
airframe.

                   (ii)   Main rotor/mast/transmission assemblies compliantly mounted to the
airframe.

                    (iii)  Main rotor supported through a bearing arrangement by a rigid
nonrotating structure with a coaxial torque shaft driving the rotor.

               (iv)   Cross-shafting, interconnect shafting, tail rotor drive shafting which
are generally supported by gearboxes at each end and by hanger bearings and
couplings at intervals along the tail rotor drive shaft.

              (v)   Engine to transmission shafting which, for compliant pylons,
incorporates a flexible or geared coupling, to accommodate the misalignment and
chucking.

               (vi)   Tail rotor/mast/gearbox supported on the tailboom or near the upper
extremity of a vertical fin.

         (4) With regard to compliant pylon mountings, recent developments in vibration
control have led to rotor isolation wherein the fuselage is isolated from the rotor and
transmission, resulting in improved vibration and system reliability. Rotor isolation
systems typically entail the installation of isolation devices at the transmission-airframe
interface. The crux of rotor isolation is providing adequate, low-frequency isolation
without excessive relative displacement or loss of mechanical stability. Rotor isolation
affects shaft critical speeds in the following ways:

                  (i)     First, the transmission mounting configuration, system stiffness, and
tuning requirements may result in different fore-and-aft and lateral natural frequencies,
imposing additional analytical requirements. For compliant mounting, the response
while transitioning through the fundamental or rocking modes is generally controlled by
dampers or elastomeric elements.

                   (ii)   Second, the relatively high displacements permitted by the isolation
system, depending on configuration, may result in variations in shaft misalignment and
length thus adding further complexity to the analytical prediction of critical speeds.

     b. Procedures.



Page E - 22

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →