FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-21

PDF page 435 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 435
AC 27-1B · E-21Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

lubricant as described above, with nominal cruise torque applied (reacted as
appropriate at main mast and tail rotor output quills), and with a vertical load at the mast
equal to gross weight of the rotorcraft at 1g, disconnect or cause to leak an external oil
plumbing device. Upon illumination of the low oil pressure warning (required by
§ 27.1305), reduce engine input torque to zero to simulate autorotation, and continue
rotation for 15 minutes. Apply input torque to simulate a minimum power landing for
approximately 15 seconds to complete the test. Successful demonstration may involve
limited damage to the transmission provided it is determined that the autorotative
capabilities of the rotorcraft were not significantly impaired.

AC 27.927A.    § 27.927 (Amendment 27-23) ADDITIONAL TESTS.

     a. Explanation. Amendment 27-23 changed § 27.927 by adding a requirement
that the rotor drive system overtorque tests prescribed by § 27.927(b)(3) be conducted
at the maximum rotational speed intended for the power condition of the test. The
previous rule only specified the torque to be applied to the rotor drive system during the
overtorque test.

     b. Procedures. The changes to this section did not change the suggested method
of compliance.

AC 27.931.  § 27.931 SHAFTING CRITICAL SPEEDS.

     a. Explanation.

         (1) At certain speeds, rotating shafts tend to vibrate violently in a transverse
direction. These speeds are variously known as “critical speeds,” “whirling speeds,” or
“whipping speeds.” The vibration results from the unbalance of the rotating system and
can be shown to reach destructive values with only minimal unbalance. The nature of
this phenomena is that as shaft rotational speed increases, residual unbalance in the
shaft gives rise to centrifugal forces. These forces cause the shaft to rotate in a bent or
bowed configuration with the centrifugal force induced bending loads being balanced by
coriolis and elastic forces in the shaft. As shaft rotational speed increases, the
centrifugal forces increase to the point at which they exceed the elastic forces in the
shaft, and divergence occurs. This point in the speed range is called the critical speed.
At shaft speeds above the critical speed, a 180° phase change occurs, the shaft’s mass
center moves toward the center of rotation, and the amplitude of vibration diminishes
with further increases in shaft speed.

         (2) A design option would be to operate the shafting subcritical; i.e., below the
first critical speed, with adequate margins between critical speed and the maximum
allowable speed, including transients. However, another option, that of supercritical
shaft operation; i.e., operating above the first or even higher critical speeds with
adequate margins between any critical speed for the normal operating speed range may
be permitted. This latter option requires some form of system damping to permit safe



                                                       Page E - 21

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →