FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-19

PDF page 433 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 433
AC 27-1B · E-19Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

the rotorcraft. The representative bench test rig should have the ability to generate the
torques, speeds, vibration frequency, and acceleration rate generated by the rotorcraft.
The power should have the same method/path of application as that used on the
rotorcraft. The test rig should be configured with the same components used for
conducting the endurance test on the rotorcraft except that the test components not
affected by asymmetric power application may not have to be installed (i.e., if a
combining gearbox is used it may not be necessary to have the main transmission
installed on the bench test rig).

         (3) The takeoff portion of the endurance test should be accomplished on the
rotorcraft. When conducting the bench test for 30-second/2-minute OEI it is not
necessary to repeat the takeoff portion of the endurance test; however, the simulated
power failure and application of 30-second/2-minute OEI power by the remaining
engine(s) should be accomplished after the input power has stabilized at takeoff power.

AC 27.927.  § 27.927 (Amendment 27-12) ADDITIONAL TESTS.

     a. Section 27.927(a):

         (1) Explanation. This paragraph is the authority to require any special tests or
investigations to establish that the rotor drive system is safe.

         (2) Procedures. The certification engineer should review the design of the rotor
drive system and its installation and intended operation for features or conditions that
may not be adequately qualified in the tests prescribed by this part and, if necessary,
additional qualification test programs should be developed and accomplished to ensure
safe operation of the rotor drive system. Items of interest would include poorly defined
load paths associated with redundant design features, flight deflections of structure and
of mounting arrangements, and special or unusual operating procedures which may be
anticipated or proposed by the applicant.

     b. Section 27.927(b):

         (1) Explanation. This paragraph prescribes testing to qualify the rotor drive
system for the power excursions to be expected with governor-controlled engines
wherein the power from the engine(s) changes automatically to maintain rotor speed at
preselected values. At high collective flight control displacements, the normal rotor
speed droop will result in the governor-controlled engine(s) automatically accelerating to
maximum fuel flow or to any other power, speed, temperature, or torque limiting device,
regardless of crew action or artificially established limitations reflected by instrument
markings. This high power condition can occur typically during a normal landing when
the crew applies high collective to cushion ground contact or, for multiengine rotorcraft,
during any flight regime when an engine fails and the corresponding loss of power
results in drooping the rotor speed. Special tests are prescribed by this section to
provide assurance that the rotor drive system can safely sustain these conditions. The
tests of this section should be conducted without intervening disassembly, and all rotor


                                                       Page E - 19

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →