Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(2) The endurance time, cited in paragraph b(1) above, excludes the time
required to adjust power or to stabilize operating conditions. Extension of the total test
time beyond 100 hours (or extension of any test run segment beyond the minimum) will
occur if qualification for the 2 ½-minute, 30-minute, or continuous OEI optional ratings is
proposed by the applicant for rotorcraft equipped with two or more engines.
(3) The requirements in § 27.923(f) stipulate that the endurance tests
conducted at maximum continuous and 75 percent maximum continuous power should
be conducted in intervals of not less than 30 minutes. These tests may be conducted
on the ground or in flight. The takeoff power endurance test described in § 27.923(e)
should be conducted in intervals of not less than 5 minutes.
(4) The new § 27.923(k) sets forth the tests to be conducted if a continuous
OEI rating is requested. Flight control positions should be set for level flight or climb,
whichever produces the maximum forward thrust component. The anti-torque system
control should be set to react the maximum rotor torque. The torque and rotational
speed values should be the maximum for which approval is requested.
AC 27.923B. § 27.923 (Amendment 27-29) ROTOR DRIVE SYSTEM AND CONTROL
MECHANISM TESTS.
a. Explanation. Amendment 27-29 added § 27.923(e)(2) that defines qualification
tests for 30-second/2-minute OEI ratings. This new paragraph also allows for the
30-second/2-minute OEI portion of the endurance test to be accomplished on a
representative bench test facility using the drive system components which can be
adversely affected by these tests.
b. Procedures.
(1) For accomplishment of the endurance test for 30-second/2-minute OEI,
§ 27.923(e)(2) requires that 10 applications of 30-second/2-minute OEI power be
demonstrated for each power section during the 10 hour takeoff power segment of
§ 27.923(e). Each 30-second/2-minute OEI application should be conducted
immediately following a 5 minute stabilized takeoff power run. Following the 5 minute
takeoff power run, one engine must simulate a power failure and each engine providing
power after the failure must apply the maximum torque and maximum speed for use
with 30-second OEI power. This power level should be maintained for at least
30-seconds. The 30-second OEI power should then be followed by an application of
the maximum torque and maximum speed for 2-minute OEI power for at least
2 minutes. Section 27.923(e)(2) also requires that one of the 30-second/2-minute OEI
segments for each engine be accomplished from the flight idle condition.
(2) Additionally, due to the damage inflicted on the engines and the ensuing
cost caused by operating the engine at these powers, the 30-second/2-minute portion of
the endurance test can be accomplished on a bench test found to be representative of
Page E - 18
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.