FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-17

PDF page 431 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 431
AC 27-1B · E-17Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

Hydraulic pumps may be loaded by resetting hydraulic system relief valves to maintain
limit pressure (load) continuously.  If this condition is excessively severe, a method of
load cycling may be appropriate. Note that accessory loads reduce the power available
to the main rotor. Also, tail rotor loads are, insofar as the transmission is concerned,
another large accessory. Care should be taken to ensure that in-flight unloading of
these accessory drives, including the tail rotor, does not subject the main gearbox to
loads significantly beyond those qualified by endurance tests.

         (4) Gearbox Oil Tanks. Normally, gearbox oil is contained in an integral cast
sump which, for other reasons, has sufficient strength to obviate the need for pressure
tests. However, a subjective evaluation should be made to ensure that detail design
features such as sight gauges, filler caps, etc., offer adequate strength.

AC 27.923A.  § 27.923 (Amendment 27-23) ROTOR DRIVE SYSTEM AND CONTROL
          MECHANISM TESTS.

     a. Explanation. Amendment 27-23 revised § 27.923(c) to remove the references
to “engine power” to avoid confusion. Previous wording could have been interpreted to
mean tests prescribed by this section should be conducted at powers corresponding to
engine ratings established under Part 33, rather than rotorcraft powers which may be
lower than those established under Part 33, but selected by the applicant as a limit on
their product. Section 27.923(d) was revised to remove the references to “engine
power” and to clarify the test requirements for 30-minute and continuous OEI powers.
Previously, §§ 27.923(e) and (j), as they relate to the 2 ½-minute and 30-minute power
ratings, respectively, provided for only minimal testing of the capability of the rotor drive
system to sustain these powers. Amendment 27-23 amended these sections to extend
the testing to adequately assure valid qualification tests. These changes ensure the
integrity of the rotor drive system so that it will safely sustain the higher stresses
expected with actual, repeated use of these power ratings. A new § 27.923(k) was
added that provides a qualification test schedule for the new, optional, continuous OEI
rating.

     b. Procedures. The policy material pertaining to this section remains in effect with
the following additions:

         (1) Section 27.923 requires a minimum of 100 hours of endurance testing.

                  (i)   For single engine rotorcraft and others that will not have OEI ratings,
the 100-hour test is comprised of 60 hours at not less than maximum continuous power,
30 hours at not less than 75 percent maximum continuous power, and 10 hours at not
less than takeoff power.

                   (ii)   For multiengine rotorcraft for which OEI ratings are requested, the test
is comprised of 60 hours at not less than maximum continuous power, 25 hours at not
less than 75 percent maximum continuous power, 10 hours at not less than takeoff
power, and 5 hours at simulated OEI power conditions.


                                                       Page E - 17

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →