FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-16

PDF page 430 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 430
AC 27-1B · E-16Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (8) Tests described in § 27.923(h) should be conducted under the conditions of
maximum continuous power and RPM as described in § 27.923(c).

         (9) Section 27.923(i) requires 200 clutch engagements. This test is prescribed
to establish a level of reliability of clutch components installed as a part of the rotor drive
system of rotorcraft. The clutch tests apply to all clutches installed to comply with
§ 27.917(b), and each such clutch must be tested. A rotor brake is not required for
certification, although a brake of some type may be installed temporarily to facilitate
conducting the clutch testing required by this section. Clutch disengagement is also
required by this section; thus, malfunction of the disengagement feature would be a
basis for discontinuance. Some rotorcraft configurations (those with single-spool
turbine engines or reciprocating engines) include an additional clutch to decouple the
engine from the drive system to facilitate engine starting. These clutches should also
be exercised at least 200 times during this test.

        (10) Section 27.923(j) sets forth the optional tests to be conducted if a
30-minute OEI rating is requested. Flight control positions should be set for level flight
or climb, whichever produces the maximum forward thrust component, and the
antitorque system control should be set to react the maximum rotor torque. The torque
and rotational speed values should be the maximum for which approval is requested.

      c.  Additional Test Considerations.

         (1) Pressure Lubricated Gearboxes. The endurance test hardware can be
adjusted/modified to sustain high-limit oil temperature and low-limit oil pressure to
provide a basis for approval of the values listed as limits. A minimum of 20 hours at
maximum continuous torque and maximum continuous rotational speed should be
involved in the test. Other parameters such as minimum oil temperature and maximum
oil pressure may more appropriately be evaluated by bench test. The significant points
here are effects of extremely high oil pressure (due to the high viscosity of cold oil) on
any positive displacement oil pump, on filters for possible collapse, on oil coolers for
possible rupture due to internal pressure, seals, bypass valves, and most important,
adequate lubrication of gears, bearings, etc., under conditions of minimal oil flow.
Normally, an operational restriction against exceeding idle power/speed conditions until
significant warm-up occurs is prescribed. Individual component qualification tests may
provide data to meet some of these aspects.

         (2) Asymmetric Power Inputs. The existing endurance test schedule does not
necessarily provide for any asymmetric power inputs from multiengine drive system
arrangements. For this situation, the drive system should at least be subjectively
evaluated for possible hazards or excessive loads to be expected from asymmetric
torque inputs.  If required, additional testing should be considered.

         (3) Accessory Drives. Normally, all accessory drives on a gearbox will be
loaded during the endurance test. Electrical load banks or other suitable methods may
be used to ensure that the generator drives are loaded and thus properly qualified.


Page E - 16

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →