Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
b. Procedures.
(1) Section 27.923(a) requires the rotor drive system and rotor control
mechanism to be in a serviceable condition at the end of the test. Verification of this
requirement requires a complete disassembly and examination of the entire rotor drive
system and rotor control mechanism. The disassembly itself should be closely
monitored for evidence of adequate breakaway torque on all bolted fasteners. Samples
of lubrication from oil sumps and filters should be retained for spectrographic analysis,
and seals should be examined for possible damage due to test requirements. Care
should be taken to differentiate between seal damage and bearing damage due to
disassembly procedures so that the direct results of the test may be properly
considered. Close visual observation of each tooth on each gear is necessary to affirm
proper load/contact patterns and absence of excessive surface stress or scrubbing
motions. Bearings should be examined to verify that ball or roller paths are within limits,
bearing cages are undamaged, and bearing balls or rollers and their races are free from
pitting. Any evidence of bearing races turning or spinning in respective housing or
bores probably indicates design or fit deficiencies. The applicant should have available
wear limits data which include items such as distance across pins and tooth profile limits
for gears. Many of these items require special, close tolerance inspection equipment
and trained inspectors to determine compliance. In some instances, bearings, clutches,
oil pumps, etc., should be returned to the original manufacturer for a finding of
serviceability. Localized overheating usually exhibited by discolorations is an indication
of an unsatisfactory condition. Should any of the items discussed above or other
defects appear such that the component is unserviceable, a redesign which includes
recognizable improvements should be required before authorizing a retest. To simply
“try again” in hopes of success should not be accepted.
(2) Section 27.923(a) also prohibits intervening disassembly which might affect
test results. Generally, this simply means no disassembly whatsoever. However, some
very limited disassembly can usually be conducted provided care is used to ensure that
items such as critical fastener torques or gear backlash controls are not disturbed.
(3) Section 27.923(b) requires that each rotor drive system and control
mechanism be tested for not less than 100 hours. This endurance test is intended to
demonstrate a minimum level of reliability and proper functioning of this system. The
test should be conducted on the rotorcraft to provide the most realistic test environment.
Exceptions can be made only if a ground or flight test facility is used that closely
simulates the support and vibration conditions existing on the actual rotorcraft. The
rotor system installed on the ground test article should be the same as that used on the
flight test vehicle. If significant productivity changes are made after completion of the
tests, retesting may be required.
(4) In § 27.923(c), (d), (e), and (f), the runs should be made with the proper
torques, rotor speeds, and control positions specified by each paragraph. The controls
discussed in each paragraph are the flight controls; i.e., cyclic and directional controls
Page E - 14
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.