Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
components. Brake engagements should be conducted with and without collective
control displacement as authorized by the flight manual or a training manual.
(3) Brake component temperature measurements during a critical brake
application in conjunction with an evaluation of the general brake compartment for
compliance with § 27.863.
(4) Placards, decals, and flight manual limitations and instructions appropriate
to operate the rotor brake safely.
(5) An evaluation for hazardous failure modes as required by § 27.1309(b). If
the brake hydraulic system is integral with the rotorcraft hydraulic system, failure modes
of pressure regulators and control valves will be of interest. Mechanical cams, calipers,
and levers may be prone to seize or fail to release the brake due, in part, to corrosion
and lack of lubrication to be expected when brake components encounter high
temperature cycling.
e. Maintenance manuals should be checked for completeness in the areas of
wear limits for both pucks and disks, for disk warp limits, and for defects which induce
brake chatter. Also, maintenance data to check for proper function of pressure
modulating/relief devices should be included since misadjustments of this device can
amplify the stresses and temperatures in the system.
AC 27.923. § 27.923 (Amendment 27-12) ROTOR DRIVE SYSTEM AND CONTROL
MECHANISM TESTS.
a. Explanation.
(1) This section is intended to require demonstration that the rotor drive system,
as defined in § 27.917(d), is capable of normal operation within the limitations proposed,
without hazard of failure from excessive wear or deterioration due to mechanical loads.
The basic test is not designed and should not be expected to demonstrate safety from
oscillatory stresses normally investigated under §§ 27.571 and 27.907, although any
data generated by these tests applicable to showing compliance with §§ 27.571 and
27.907 may be used. Some variations in the endurance test plan to generate data
applicable to the vibration substantiation effort or other qualification aspects may be
acceptable if the basic requirements of the endurance test are preserved.
(2) This rule requires a series of runs consisting of a 60-hour, 30-hour, and
10-hour run for a total of (at least) 100 hours of testing, not including time required to
adjust power or to stabilize operating conditions for those conditions that require
stabilization. Extension of the total test time beyond 100 hours (or extension of any test
run segment beyond the minimum) will occur if qualification for the 2 ½-minute
one-engine-inoperative (OEI) optional rating is proposed by the applicant. The
30-minute OEI rating qualification test will extend the test beyond 100 hours for
rotorcraft equipped with three or more engines.
Page E - 12
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.