Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
SUBPART E - POWERPLANT
ROTOR DRIVE SYSTEM
AC 27.917. § 27.917 (through Amendment 27-11) DESIGN.
a. § 27.917(a):
(1) Explanation. This paragraph requires the design of the drive system to
include a means to automatically disengage the engine(s) from the rotor drive system in
order to prevent excessive drag from an inoperative engine from adversely affecting the
performance of the rotor system.
(2) Procedures. The design objective usually is met by installing a
freewheeling or overrunning clutch in the drive shaft between the engine and the first
part of rotor drive system. If lubrication for these clutches is required, it should be
provided by a means that continues to function after an engine is made inoperative
except that for single-engine rotorcraft, clutch lubrication need only be provided for
autorotation descent with the engine inoperative. A 15-minute demonstration of
freewheeling or overrunning operation is usually acceptable.
b. § 27.917(b):
(1) Explanation. This paragraph requires that control rotors (tail rotors, for
example) will continue to be driven by the main rotors when the rotorcraft is in
autorotation.
(2) Procedures. Provide hard mechanical interconnect shafting between the
rotors such that the main rotor will drive the control rotor (tail rotor). Note that this
requirement must be met with all engines inoperative, thus, the driving force for the tail
rotors must depend on the autorotative driving forces inherent in the main rotor(s).
c. § 27.917(c):
(1) Explanation. This paragraph pertains to any device or feature designed into
the rotor drive system intended to prevent damage in the event of excessive torque in
the rotor drive system from high engine power or mechanical interference with normal
rotation of the rotor drive system. The rule prohibits location of these devices in any
part of the rotor drive system that is required to continue functioning to provide control of
the rotorcraft.
(2) Procedures. Review the arrangement of the rotor drive system to determine
that any intentionally designed weak links in the system, such as shear sections or slip
clutches installed to relieve high torsional loads, are located so that their function will no
Page E – 10.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.