Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
(ii) For § 27.903(b)(1)(ii) compliance, if containment protection is not
installed, damage to any component or structure within the trajectory of the failed fan
rotor should not cause the loss of any function essential to a controlled landing.
(iii) For § 27.903(b)(1)(iii) compliance, a spin test should be conducted.
For fans driven directly by the engine, the test should be conducted at 122.5 percent of
the terminal engine rotational speed that will occur under uncontrolled conditions, or at
122.5 percent of the maximum engine rotational speed that would be controlled by a
reliable, approved engine overspeed limiting device. For fans driven by the rotor drive
system, the test should be conducted at 122.5 percent of the maximum rotor drive
system rotational speed expected in service, including transients.
(Note: Capability to withstand the ultimate load of 1.5 times the centrifugal force means
that no failure should occur and distortion should not result in fan element contact with
housings or other adjacent components during the 122.5 percent spin test which
equates to 150 percent centrifugal force).
(3) Fatigue. If the cooling fan is not included in the fatigue evaluation under
§ 27.571, it should be shown that the cooling fan blades are not operating at resonant
conditions within the normal operating limits of the rotorcraft.
AC 27.903B. §27.903 (Amendment 27-44) ENGINES.
a. Explanation. Amendment 27-44, § 27.903(d) requires that any engine must
have a restart capability that has been demonstrated throughout a flight envelope to be
certificated for the rotorcraft.
b. Procedures.
and landing maximum altitude and temperature limits. Compliance is usually shown by
conducting actual in-flight restarts during flight tests or other tests in accordance with an
approved test plan. However, § 27.903(d)(1) does not require in-flight demonstration of
restart capability for single-engine rotorcraft or for all-engine shutdown of multi-engine
rotorcraft. In the past, engine relight capability for single engine rotorcraft has been
demonstrated on the ground taking into account altitude effects, warm engine
characteristics, depleted battery, etc. Restarts should be conducted at various altitudes,
ambient temperatures, and fuel temperatures using the fuel type most critical, unless the
applicant can show that this parameter is not pertinent. Other concerns involve the pilot
station arrangement for flight controls and engine starting controls. It should be verified
that the engine start can be accomplished without jeopardizing continued safe operation
of the rotorcraft. Pilot workload for a preexisting one engine inoperative (OEI) situation,
the location of the restart system controls, and the availability of a second pilot should be
considered. The emergency and malfunction instruction sections of the rotorcraft flight
manual (RFM) should present a detailed definition of the approved restart envelope and
detailed instructions for the restart.
Page E - 9
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.