Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
ensure that certification requirements are not overlooked when reciprocating engines
are installed in rotorcraft to be certified under Part 27 requirements. Section (b) was
revised to prescribe tests and qualifications for powerplant area cooling fans. This rule
change requires cooling fans to be designed and installed to enable safe landing of the
rotorcraft following a fan blade failure. Compliance with the previous requirements
could result in hazards to the rotorcraft with the loss of cooling air to critical powerplant
components. A new paragraph was also added to the rule for cooling fans, which are
part of the powerplant installation. It should be determined that no cooling fan blade
resonant conditions exist within the operating limits of the rotorcraft unless a fatigue
evaluation is conducted. These requirements will ensure that correct qualification
procedures are used for rotorcraft engines and that all powerplant cooling fans are
properly tested.
b. Procedures.
(1) Engine type certification. All engines installed in rotorcraft should have a
type certificate. The specific certification requirements for reciprocating engines when
installed in rotorcraft are found in the paragraph listed in Part 33. Engines certificated
under other approved certification rules (CAR Part 13 and FAR § 21.29, for imported
engines) are also eligible. If a component, system, or arrangement is certified under
Part 33 or other requirement, the applicant is not relieved of the necessity to comply
with the requirements of Part 27. If the component, system, or arrangement, supplied
as a part of a certificated engine, meets the Part 33 and Part 27 requirements,
subsequent changes to these components, systems, or arrangements could negate
compliance with Part 27.
(2) The applicant may select §§ 27.903(b)(1)(i), (b)(1)(ii), or (b)(1)(iii) to show
compliance with this section.
(i) For compliance with § 27.903(b)(1)(i), a demonstration should be
conducted to show that at the expected maximum fan speed, a failed blade will be
contained within a housing or shroud that is included in the proposed type design and
designated as the containment shield. The maximum fan rotational speed may be
related to an overspeed limiting device or to the expected maximum transient speed
from analysis or test of the engine, system, or component which drives the fan. For
fans driven directly by the engine, output shaft disconnect and the subsequent terminal
speed of the engine may establish the maximum fan speed for the test condition. To
conduct an overspeed blade failure containment demonstration, applicants have found it
convenient to progressively weaken a blade to induce failure at or above the required
demonstration speed. Blade failure may be expected to subsequently occur on some or
all of the remaining blades. This condition, provided all blades are contained, is
acceptable for showing compliance with this rule. However, the corresponding loss of
cooling may be unacceptable if it causes the loss of any function essential to continued
safe flight and landing.
Page E - 8
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.